Epson AcuLaser C2600N User Manual

							Using the Control Panel231
7
7
7
7
7
7
7
7
7
7
7
7
*1Default paper sizes are automatically detected.
*2Custom-size paper: 98 × 148 minimum, 216 × 297 maximum.
*3Available only when the optional Duplex Unit is installed.
Page Size
Specifies the paper size.
Wide A4
Selecting On decreases the left and right margins from 4 mm to 
3.4 mm.
Orientation
Specifies whether the page is printed in portrait or landscape 
orientation.
Resolution
Item Settings (default in bold)
Page Size
*1A4*1, A5, B5, LT*1, HLT, GLT, EXE, MON, C10, DL, 
C5, C6, IB5, CTM*2
Wide A4Off, On
OrientationPort, Land
Resolution600, 300
RITechOn, Off
Toner SaveOff, On
Image OptimumAuto, Off, On
Top Offset -99.0 ... 0.0 ... 99.0 mm in 0.5 increments
Left Offset -99.0 ... 0.0 ... 99.0 mm in 0.5 increments
Top Offset B
*3-99.0 ... 0.0 ... 99.0 mm in 0.5 increments
Left Offset B
*3-99.0 ... 0.0 ... 99.0 mm in 0.5 increments
 
						

							232Using the Control Panel Specifies the printing resolution.
RITech
Turning RITech on produces smoother and crisper lines, text, and 
graphics.
Toner Save
When this setting is selected in the B/W and 4 × B/W modes, the 
printer saves toner by substituting a gray shade for the black 
inside of characters. The characters are outlined in full black on 
the right and lower edges.
When this setting is selected in the Color mode, the printer saves 
toner by using half the normal amount of toner.
Image Optimum
When this mode is on, the quality of graphics is reduced. It 
reduces the amount of graphics data when the data reaches the 
memory limit, allowing complex documents to be printed.
Top Offset
Makes fine adjustments to the vertical printing position of the 
page.
c
Caution:
Make sure that the printed image does not extend beyond the edge 
of the paper. Otherwise, you may damage the printer.
Left Offset
Makes fine adjustments to the horizontal printing position of the 
page. This is useful for fine adjustments.
 
						

							Using the Control Panel233
7
7
7
7
7
7
7
7
7
7
7
7
c
Caution:
Make sure that the printed image does not extend beyond the edge 
of the paper. Otherwise, you may damage the printer.
Top Offset B
Adjusts the vertical printing position on the back of the paper 
when printing on both sides. Use this if the printout on the back 
is not where you expected.
Left Offset B
Adjusts the horizontal printing position on the back of the paper 
when printing on both sides. Use this if the printout on the back 
is not where you expected.
Setup Menu
This menu allows you to make various basic configuration 
settings related to paper sources, feeding modes, and error 
handling. You can also use this menu to select the LCD panel 
display language.
 
						

							234Using the Control Panel
*1Available only when the corresponding option is installed.
*2Available only for PCL5e, ESC/Page, ESC/P2, FX, or I239X mode.
Lang
Specifies the language displayed on the LCD panel and that 
printed on the status sheet.
Time Out
Item Settings (default in bold)
LangEnglish, Français, Deutsch, Italiano, 
ESPAÑOL, SVENSKA, Dansk, Nederlands., 
SUOMI, Português,  , 
Time Out 0, 5 to 60 to 300 in increments of 1
Paper SourceAuto, MP, LC1, LC2
*1
MP ModeNormal, Last
Manual FeedOff, 1st page, Each page
Copies1 to 999
Duplex
*1Off, On
Binding
*1Long Edge, Short Edge
Start Page
*1Front, Back
Paper TypeNormal, Thick, Trnsprnc, Rough
Page SideFront, Back
Skip Blank Page
*2Off, On
Auto Eject PageOff, On
Size IgnoreOff, On
Auto ContOff, On
Page ProtectAuto, On
Toner OutStop, Continue
LCD Contrast 0 to 7 to 15
 
						

							Using the Control Panel235
7
7
7
7
7
7
7
7
7
7
7
7
Specifies the length of the time, in seconds, before a time out when 
interfaces are being switched automatically. The time before a 
time out occurs is the length of time from the point when no data 
is being received from an interface until the point of switching the 
interface. If the printer has a print job when switching the 
interface, the printer prints the print job.
Paper Source
Specifies whether paper feeds into the printer from the MP tray 
or the optional paper cassette unit.
If you select Auto, paper feeds from the paper source containing 
paper that matches your Paper Size setting.
If an envelope size (C5, C6, C10, DL, MON, or IB5) is selected as the 
Page Size setting, paper always feeds from the MP tray. If you 
select Thick or Trnsprnc as the Paper Type setting, paper always 
feeds from the MP tray.
MP Mode
This setting determines whether the MP tray has the highest or 
lowest priority when Auto is selected as the Paper Source setting 
in the printer driver. When Normal is selected as the MP Mode, 
the MP tray has the highest priority as the paper source. If you 
select Last, the MP tray has the lowest priority.
Manual Feed
Allows you to select the manual feed mode for the MP tray.
Copies
Designates the number of copies to be printed, from 1 through 
999.
Duplex
 
						

							236Using the Control Panel Turns duplex printing on or off.
Binding
Specifies the binding direction of the printout.
Start Page
Specifies whether printing starts from the front or back of the 
page.
Paper Type
Specifies the type of paper to be used for printing. The printer 
adjusts the printing speed according to this setting. The printing 
speed is reduced when Thick or Trnsprnc is selected.
Page Side
Select Front when printing on the front of thick paper (Thick).
Select Back when printing on the back of thick paper (Thick).
Skip Blank Page
Enables you to skip blank pages when printing. This setting is 
available when you print in the PCL5e, ESC/Page, ESCP2, FX, or 
I239X mode.
Auto Eject Page
Specifies whether or not to eject paper when the limit specified in 
the Time Out setting is reached. The default is Off, which means 
paper is not ejected when the time-out limit is reached.
Size Ignore
 
						

							Using the Control Panel237
7
7
7
7
7
7
7
7
7
7
7
7
If you want to ignore a paper size error, select On. When you turn 
this item on, the printer keeps printing even if the image size 
exceeds the printable area for the specified paper size. This may 
cause smudges because of the toner that is not transferred onto 
the paper properly. When this item is turned off, the printer stops 
printing if a paper size error occurs.
Auto Cont
When you turn this setting on, the printer automatically continues 
printing after a certain period of time when one of the following 
errors occurs: Paper Set, Print Overrun, or Mem Overflow. When 
this option is off, you must press the NStart/Stop button to 
resume printing.
Page Protect
Allocates additional printer memory for printing data, as 
opposed to receiving it. You may need to turn this setting on if 
you are printing a very complex page. If a Print Overrun error 
message appears on the LCD panel during printing, turn this 
setting on and reprint your data. This reduces the amount of 
memory reserved for processing data so your computer may take 
longer to send the print job, but it will allow you to print complex 
jobs. Page Protect usually works best when Auto is selected. You 
will need to increase your printer’s memory if memory errors 
continue to occur.
Note:
Changing the Page Protect setting reconfigures the printer’s memory, 
which causes any downloaded fonts to be deleted.
Toner Out
If the item is set to Stop, the printer lets you know when the toner 
is out. To disable this function, set this item to Continue. 
 
						

							238Using the Control Panel Note:
If this item is set to Continue, the print result may be different from 
what you expected because there may not be enough toner to print the 
data.
LCD Contrast
Adjusts the contrast of the LCD panel. Use the uUp and dDown 
buttons to set the contrast between 0 (lowest contrast) and 15 
(highest contrast.)
Mode Config. Menu
This menu allows you to switch the printing mode. You can also 
use this menu to stop using one of the black toner cartridges when 
the printer is in the 4 × B/W mode.
* Available only in the 4 × B/W mode.
Remove All Toner
Removes all toner cartridges. Use this function before 
transporting the printer.
Change mode B/W
Item Settings (default in bold)
Remove all toner -
Change Mode 4 × 
B/W-
Change Mode Color -
KC Toner*Enable, Disable
KM Toner*Enable, Disable
KY Toner*Enable, Disable
KK Toner*Enable, Disable
 
						

							Using the Control Panel239
7
7
7
7
7
7
7
7
7
7
7
7
Switches to the B/W mode, which is the monochrome printing 
mode with only one black toner cartridge installed.
Change mode 4 × B/W
Switches to the 4 × B/W mode, which is the monochrome printing 
mode with four black toner cartridges installed.
Change mode Color
Switches to the Color mode, which is the color printing mode with 
the C, M, and Y toner cartridges installed.
KC/KM/KY/KK Toner
This setting is available only when the printer is in the 4 × B/W 
mode. When you find a faint printing pattern on the Toner Check 
Sheet, set the indicated toner cartridge to Disable to maintain 
printing quality. 
Reset Menu
This menu allows you to cancel printing and reset the printer 
settings.
Clear Warning
Clears warning messages that show errors except for these that 
occur from consumable products or mandatory-replacement 
parts.
Clear All Warnings
Clears all warning messages that appear on the LCD panel.
Reset
 
						

							240Using the Control Panel Stops printing and clears the current job received from the active 
interface. You may want to reset the printer when there is a 
problem with the print job itself and the printer cannot print 
successfully.
Reset All
Stops printing, clears the printer memory, and restores the printer 
settings to their default values. The print jobs received from all 
interfaces are erased.
Note:
Performing Reset All clears print jobs received from all interfaces. Be 
careful not to interrupt someone else’s job.
SelecType Init
Restores the control panel menu settings to their default values.
Change Toner C/M/Y/K
Replace the indicated toner cartridge. See  Toner Cartridge on 
page 315 for details.
Quick Print Job Menu
This menu allows you to print or delete print jobs that were stored 
in the printer’s Hard Disk Drive using the Quick Print Job feature 
(Re-Print Job, Verify Job, Stored Job) of the printer driver’s 
Reserve Job function. For instructions on using this menu, see  
Using the Quick Print Job Menu on page 278.