Epson AcuLaser C2600N User Manual
Have a look at the manual Epson AcuLaser C2600N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Using the Control Panel271 7 7 7 7 7 7 7 7 7 7 7 7 The installed toner cartridge is not a genuine Epson toner cartridge. Using a non-genuine toner cartridge may affect print quality. Epson shall not be liable for any damages or problems arising from the use of consumable products not manufactured or approved by Epson. Installing a genuine toner cartridge is recommended. Press the NStart/Stop button on the control panel to resume printing. Offline The printer is not ready to print. Press the NStart/Stop button. Optional RAM Error The optional memory module may be corrupted or incorrect. Replace it with a new one. Paper Jam WWWW The location where the paper jam occurred is displayed at WWWWW. WWWWW indicates the location of the error. If a paper jam occurs at two or more locations simultaneously, the corresponding multiple locations are displayed. Location Description Jam A Paper is jammed at cover A. For instructions on how to remove jammed paper at cover A, see Jam A (cover A) on page 346. Jam A, B Paper is jammed at cover B. For instructions on how to remove jammed paper at cover B, see Jam A, B (cover A and B) on page 349. Jam MP, A Paper is jammed at the MP tray. For instructions on how to remove jammed paper at the MP tray, see Jam MP, A (MP tray and cover A) on page 356.
272Using the Control Panel Paper Out tttt sssss There is no paper in the specified paper source (tttt). Load paper of the size (sssss) into the paper source. Paper Set tttt sssss The paper loaded in the specified paper source (tttt) does not match the required paper size (sssss). Replace the loaded paper with the correct size paper and press the NStart/Stop button to resume printing, or press the +Cancel Job button to cancel the print job. If you press the NStart/Stop button without replacing the paper, the printer will print on the loaded paper even though it does not match the required size. Please Shutdown This message appears after all the toner cartridges are removed. Turn off the printer. Please Wait The toner cartridge to be replaced is moving to the replacement position in the printer. Printer Open Cover D, B, A, or E is open. Close all the covers. Jam A, C1 Paper is jammed at the standard lower paper cassette. For instructions on clearing this type of paper jam, see Jam A, C1 (cover A and standard lower paper cassette) on page 359. Jam A, E, C2Paper is jammed at the optional paper cassette. For instructions on clearing this type of paper jam, see Jam A, E, C2 (cover A, E, and optional paper cassette) on page 364.
Using the Control Panel273 7 7 7 7 7 7 7 7 7 7 7 7 Print Overrun The required time to process the print data exceeded the print engine speed because the current page is too complex. Press the NStart/Stop button to resume printing, or press the +Cancel Job button to cancel the print job. If this message appears again, select On as the Page Protect setting in the control panel’s Setup Menu or select Avoid Page Error on the printer driver. If you continue to receive this message when printing a particular page, try simplifying the page by limiting the number of graphics or reducing the number and size of fonts. To avoid this error, it is recommended that you set the Page Protect setting to On and add more memory to the printer. See Setup Menu on page 233 and Memory Module on page 303 for details. PS3 Hard Disk full The memory allocated for writing PostScript 3 commands on the optional Hard Disk Drive is full. To clear this error, select Clear Warning from the control panel’s Reset Menu, or remove the downloaded PS fonts to make room on the Hard Disk Drive. For instruction about accessing the control panel menus, see How to access the control panel menus on page 223. RAM CHECK The printer is checking the RAM. Ready The printer is ready to receive data and print. Remove Toner
274Using the Control Panel This message appears when the printer switches to the B/W mode. See Switching the Printing Mode on page 283 to find how to switch the mode. Replace Fuser The fuser has reached the end of its service life. Turn the printer off, then replace the fuser unit with a new one. See Fuser Unit on page 326 for instructions. Replace Photoconductor The photoconductor has reached the end of its service life. Turn off the printer, then replace the photoconductor unit with a new one. See Photoconductor Unit on page 319 for instructions. The error clears automatically after you replace the unit, then close all printer covers. The photoconductor service life counter is reset automatically. When the error light is blinking, you can continue printing by pressing the NStart/Stop button. However, the print quality is not guaranteed from then on. Replace Toner uuuu The indicated toner cartridges are out of toner and need to be replaced. (The letters C, M, Y, or K appear in place of uuuu and indicate the colors Cyan, Magenta, Yellow, and Black respectively.) See Toner Cartridge on page 315 for instructions. Replace Waste T Box The waste toner collector is full of toner. Replace it with a new waste toner collector. See Waste Toner Collector on page 331 for instructions.
Using the Control Panel275 7 7 7 7 7 7 7 7 7 7 7 7 Reserve JobCanceled The printer cannot store the data of your print job using the Reserve Job function. The maximum number of print jobs stored on the printer’s Hard Disk Drive has been reached, or the drive has no more memory available to store a new job. To store a new print job, delete a previously stored job. Also, if you have any Confidential Jobs stored, printing those jobs will make more memory available. To clear this error, select Clear Warning from the control panel’s Reset Menu. For instruction about accessing the control panel menus, see How to access the control panel menus on page 223. Reset The printer’s current interface has been reset and the buffer has been cleared. However, other interfaces are still active and retain their settings and data. Reset All All printer settings have been reset to the default configuration, or to the last settings that were saved. Reset to Save A control panel menu setting was changed while the printer was printing. Press the NStart/Stop button to clear this message. The setting will become effective after printing has finished. Alternatively you can clear this message by performing Reset or Reset All on the control panel. However, the print data will be deleted. ROM CHECK The printer is checking the ROM. SELF TEST
276Using the Control Panel The printer is currently performing a self test and initialization. Service Req Cffff/Service Req Eggg A controller error or a print engine error has been detected. Turn off the printer. Wait at least 5 seconds, then turn it back on. If the error message still appears, write down the error number listed on the LCD panel (Cffff/Eggg), turn off the printer, unplug the power cord, then contact a qualified service representative. Sleep The printer is currently in the power-save mode. This mode is canceled when the printer receives print data. This mode is also canceled by selecting Reset or Reset All from the control panel’s Rest Menu. See Using the Control Panel Menus on page 223 for instructions. TonerCart Error uuuu A read/write error has occurred for the indicated toner cartridges (The letters C, M, Y, or K appear in place of uuuu and indicate the colors Cyan, Magenta, Yellow, and Black respectively.). Remove the toner cartridges and reinsert them. If that fails to clear the error, replace the toner cartridges. To install the indicated cartridges. See Toner Cartridge on page 315. Turn Paper Paper on the MP tray is not loaded correctly. Remove the paper and load it correctly on the MP tray. Unable Clear Error The printer cannot clear an error message because the error status still remains. Try solving the problem again.
Using the Control Panel277 7 7 7 7 7 7 7 7 7 7 7 7 uuuu Toner Low This message indicates that the toner cartridge for the indicated color is near the end of its service life. Prepare a new toner cartridge. Warming Up The printer is warming up the fuser to be ready to print. Waste Toner Box Near Full The waste toner collector is near full of toner. Worn Fuser This message indicates that the fuser unit is near the end of its service life. Printing after this message appears is not guaranteed. Turn the printer off, then reinstall the unit after it has cooled off (30 minutes). Then replace the fuser unit with a new one. See Fuser Unit on page 326 for instructions. The error clears automatically after you replace the unit and close all printer covers. Worn Photoconductor This message indicates that the photoconductor unit is near the end of its service life. Printing after this message appears is not guaranteed. Turn the printer off, then replace the photoconductor unit with a new one. See Photoconductor Unit on page 319 for instructions. The error clears automatically after you replace the unit and close the printer covers. Worn Transfer Unit This message warns you that the transfer unit is near the end of its service life. Contact your dealer.
278Using the Control Panel To clear this warning message and continue printing, select Clear All Warning from the control panel’s Reset Menu. For instruction about accessing the control panel menus, see How to access the control panel menus on page 223. Write Error ROM P The printer is unable to write data into the ROM module correctly. You cannot remove the ROM P because the ROM P is a program ROM module. Contact your dealer. Writing ROM A/Writing ROM P This message indicates that a ROM module in the slot is being written. Please wait until this message disappears. Printing and Deleting Reserve Job Data Print jobs stored on the printer’s optional Hard Disk Drive using the Re-Print Job, Verify Job, and Stored Job options of the Reserve Job function can be printed and deleted using the control panel’s Quick Print Job Menu. Jobs saved using the Confidential Job option can be printed from the Confidential Job Menu. Follow the instructions in this section. Using the Quick Print Job Menu Follow the steps below to print or delete Re-Print Job, Verify Job, and Stored Job data. 1. Make sure the LCD panel displays Ready or Sleep, then press the Enter button to access the control panel menus. 2. Press the dDown button repeatedly until Quick Print Job Menu appears on the LCD panel, then press the Enter button.
Using the Control Panel279 7 7 7 7 7 7 7 7 7 7 7 7 3. Use the dDown or uUp button to scroll to the appropriate user name, then press the Enter button. 4. Use the dDown or uUp button to scroll to the appropriate job name, then press the Enter button. 5. To specify the number of copies you want to print, press the Enter button, then use the dDown and uUp buttons to select the number of copies. To delete the print job without printing any copies, press the dDown button to display Delete on the LCD panel. 6. Press the Enter button to start printing or to delete the data. Using the Confidential Job Menu Follow the steps below to print or delete Confidential Job data. 1. Make sure the LCD panel displays Ready or Sleep, then press the Enter button to access the control panel menus. 2. Press the dDown button repeatedly until ConfidentialJobMenu appears on the LCD panel, then press the Enter button. 3. Use the dDown or uUp button to scroll to the appropriate user name, then press the Enter button.
280Using the Control Panel 4. Enter your four-digit password by using the corresponding buttons, as shown below. Note: ❏Passwords are always four digits. ❏Passwords consist of numbers from 1 through 4. ❏If no print jobs have been saved with the password you entered, Password Error appears briefly on the LCD panel then the printer exits the control panel menus. Confirm the password and try again. 5. Use the dDown or uUp button to scroll to the appropriate job name, then press the Enter button. 6. To specify the number of copies you want to print, press the Enter button, then use the dDown and uUp buttons to select the number of copies. To delete the print job, press the dDown button to display Delete on the LCD panel. 7. Press the Enter button to start printing or to delete the data.