Home > Epson > Printer > Epson AcuLaser C2600N User Manual

Epson AcuLaser C2600N User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C2600N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 473
    							Using the Control Panel261
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    Adjust the density of the printing for back side of normal paper. 
    The setting becomes darker as the value increases.
    Thick
    Adjust the density for thick paper. The setting becomes darker as 
    the value increases.
    Trnsprnc
    Adjust the density for transparencies. The setting becomes darker 
    as the value increases.
    Envelope
    Adjust the density for envelopes. The setting becomes darker as 
    the value increases.
    Highland
    Prevents printing defects caused by abnormal electric discharge 
    that may occur when using the printer in locations at high 
    altitudes. Select 1 when using the printer in locations at high 
    altitudes.
    Feed Offset
    Adjust the vertical position in which to start printing. The position 
    moves lower on the sheet as the value increases. This setting is 
    used when doing single-sided printing or printing the first page 
    for duplex printing.
    Scan Offset
    Adjust the horizontal position in which to start printing. The 
    position moves to the right of the sheet as the value increases. This 
    setting is used when doing single-sided printing or printing the 
    first page for duplex printing.
     
    						
    							262Using the Control Panel Feed Offset2
    Adjust the vertical position in which to star printing. The position 
    moves lower on the sheet as the value increases. This setting is 
    used when printing the printing on the backside of paper for 
    duplex printing.
    Scan Offset2
    Adjust the horizontal position in which to start printing. The 
    position moves to the right of the sheet as the value increases. This 
    setting is used when printing on the backside of paper for duplex 
    printing.
    Status and Error Messages
    This section contains a list of error messages shown on the LCD 
    panel, giving a brief description of each message and suggestions 
    for correcting the problem. Note that not every message shown 
    on the LCD panel indicates a problem. When the   mark is 
    displayed at the left of the warning message, multiple warnings 
    occur. To confirm all warnings that occur, press the dDown 
    button to display the Status Menu, then press the Enter button. 
    The LCD panel also displays the amounts of remaining toners and 
    available paper sizes.
    Calibrating Printer
    The printer automatically calibrates itself. This is not an error 
    message, and will clear itself after the calibration process has 
    finished. While the printer displays this message, do not open the 
    covers or turn off the printer.
    Cancel All Print Job
     
    						
    							Using the Control Panel263
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    The printer is canceling all print jobs in the printer memory, 
    including jobs the printer is currently receiving or printing. This 
    message appears when the +Cancel Job button has been 
    pressed down for more than 2 seconds.
    Cancel Print Job
    The printer is canceling the current print job. This message 
    appears when the +Cancel Job button has been pressed and 
    released within 2 seconds.
    Cancel Print Job (by host)
    The print job is canceled at the printer driver.
    Can’t Print
    The print data is deleted because it is incorrect.
    Make sure that the appropriate paper size is set and appropriate 
    your printer driver is used.
    Can’t Print Duplex
    The printer has encountered problems during duplex printing. 
    Make sure you are using an appropriate type and size of paper 
    for the Duplex Unit. The problem could also be a result of 
    incorrect settings for the paper source you are using. Pressing the 
    NStart/Stop button will print the rest of the print job on only one 
    side of the paper. Press the +Cancel Job button to cancel the 
    print job.
    Change Toner to X
    This message appears when the printer switches from the 4 × 
    B/W mode to Color 4 mode. (The letter C, M, or Y appears in place 
    of X and indicates the colors Cyan, Magenta, or Yellow 
    respectively.) See  Switching the Printing Mode on page 283 to 
    find how to switch the mode.
     
    						
    							264Using the Control Panel Check Paper Size
    The paper size setting is different from the size of paper loaded 
    in the printer. Check to see if the correct size of paper is loaded in 
    the specified paper source.
    To clear this error, select Clear Warning from the control panel’s 
    Reset Menu. See  How to access the control panel menus on page 
    223 for instructions.
    Check Paper Type
    The media loaded in the printer does not match the paper type 
    setting in the printer driver. Media that matches only the paper 
    size setting will be used for printing.
    To clear this error, select Clear Warning from the control panel’s 
    Reset Menu. See  How to access the control panel menus on page 
    223 for instructions.
    Clean Parts v v
    Indicates that the printer needs to be cleaned using the cleaning 
    knob [a] or [b] (indicated as vv). See  Cleaning the 
    photoconductor wire (knob [a]) on page 338 or  Cleaning the 
    exposure window (knob [b]) on page 339 for instructions.
    Clean Sensor
    The sensor inside the printer needs to be cleaned. To clean the 
    sensor, open cover D and close it again. 
    Collate Disabled
    Printing by specifying the number of copies is no longer possible 
    due to a lack of memory (RAM) or free disk space on the optional 
    Hard Disk Drive. If this error occurs, print only one copy at a time.
     
    						
    							Using the Control Panel265
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    To clear this error, select Clear Warning from the control panel’s 
    Reset Menu. For instruction about accessing the control panel 
    menus, see  How to access the control panel menus on page 223.
    Color Data Received
    The printer receives color printing data when it is in the B/W or 
    4 × B/W mode. Press the NStart/Stop button to print the data in 
    monochrome, or press the +Cancel Job button to cancel the 
    print job.
    Cooling Down
    The printer lowers its temperature to optimize for the fixing toner. 
    Wait for a moment for Ready to appear in the LCD panel.
    Duplex Memory Overflow
    There is not enough memory for duplex printing. The printer 
    prints only on the front and ejects the paper. To clear this error, 
    follow the instructions below.
    If Off is selected as the Auto Cont setting on the control panel’s 
    Setup Menu, press the NStart/Stop button to print on the back 
    of the next sheet, or press the +Cancel Job button to cancel the 
    print job.
    If On is selected as the Auto Cont setting on the control panel’s 
    Setup Menu, printing continues automatically after a certain 
    period of time.
    Formatting HDD
    The Hard Disk Drive is being formatted.
    Form Data Canceled
     
    						
    							266Using the Control Panel Unable to store form overlay data on the printer’s optional Hard 
    Disk Drive. Either the drive is full, or the maximum number of 
    form overlay files has been reached. Delete any form overlay files 
    you no longer need, then try storing the new overlay again.
    To clear this error, select Clear Warning from the control panel’s 
    Reset Menu. For instruction about accessing the control panel 
    menus, see  How to access the control panel menus on page 223.
    Form Feed
    The printer is ejecting paper due to a user request. This message 
    appears when pressing the NStart/Stop b u t t on  o n ce  t o m a k e t he  
    printer offline, then holding down the NStart/Stop button for 
    more than 2 seconds in order not to receive form feed command.
    Format Error ROM A
    An unformatted ROM module has been inserted. 
    To clear this error, either press the NStart/Stop button or turn off 
    the printer and remove the ROM module, then reinstall the ROM 
    module. If that fails to clear the error, contact your dealer.
    Hard Disk Full
    The optional Hard Disk Drive is full and you cannot save any 
    data. Delete the unnecessary data from the Hard Disk Drive. To 
    clear this error, select Clear Warning from the control panel’s 
    Reset Menu. For instruction about accessing the control panel 
    menus, see  How to access the control panel menus on page 223.
    HDD CHECK
    The printer is checking the Hard Disk Drive.
    Image Optimum
     
    						
    							Using the Control Panel267
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    There is insufficient memory to print the page at the specified 
    print quality. The printer automatically lowers the print quality 
    s o  t h a t  i t  c a n  c o n t i n u e  p r i n t i n g .  I f  t h e  q u a l i t y  o f  t h e  p r i n t o u t  i s  n o t  
    acceptable, try simplifying the page by limiting the number of 
    graphics or reducing the number and size of fonts.
    To clear this error, select Clear Warning from the control panel’s 
    Reset Menu. See  How to access the control panel menus on page 
    223 for instructions.
    Turn the Image Optimum setting off on the control panel’s Printing 
    Menu if you do not want the printer to automatically lower the 
    print quality to continue printing.
    You may need to increase the amount of printer memory to be 
    able to print at the desired print quality for your document. For 
    more information on adding memory, see  Memory Module on 
    page 303.
    Install Fuser
    There is no fuser unit installed or the fuser unit is not installed 
    properly. Turn off the printer, then install the fuser unit if it is not 
    installed. 
    If a fuser unit is already installed, turn the printer off and reinstall 
    the unit after it has cooled off (30 minutes). Open covers A and B. 
    Remove the fuser unit, then reinstall it properly. Close covers A 
    and B. The error clears automatically if the fuser unit is properly 
    installed. 
    If the error is not cleared, the fuser unit is out of order. Replace it 
    with a new fuser unit.
    Install Photoconductor
    There is no photoconductor unit installed or the photoconductor 
    unit is not installed properly. Turn off the printer and install the 
    photoconductor unit if it is not installed.
     
    						
    							268Using the Control Panel If a photoconductor unit is already installed, confirm cover D is 
    closed. Otherwise, turn off the printer, open cover D. Remove the 
    photoconductor unit, then reinstall it properly. Close cover D. The 
    error clears automatically if the photoconductor unit is properly 
    installed. 
    Install uuuu TnrCart
    The indicated toner cartridges are not installed in the printer. (The 
    letters C, M, Y, or K appear in place of uuuu and indicate the colors 
    Cyan, Magenta, Yellow, and Black respectively.)
    Install the indicated cartridges. See  Toner Cartridge on page 
    315.
    Install Waste T Box
    The waste toner collector is not installed, or is installed 
    incorrectly. If there is no waste toner collector installed, install one 
    in the printer. If there is a waste toner collector already installed, 
    try removing it and reinstalling it. See  Waste Toner Collector 
    on page 331 for instructions.
    Invalid AUX I/F Card
    This message means that the printer cannot communicate with 
    the installed optional interface card. Turn off the printer, remove 
    the card, then reinstall it.
    Invalid Data
    The spool file on the driver is deleted while printing or the data 
    is abnormal. Press the NStart/Stop button to clear the error.
    Invalid HDD
    Either the optional Hard Disk Drive is damaged or it cannot be 
    used with this printer. Turn off the printer, then remove the Hard 
    Disk Drive.
     
    						
    							Using the Control Panel269
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    Invalid N/W Module
    There is no network program, or the network program cannot be 
    used with your printer. Contact a qualified service representative.
    Invalid P5C
    The optional P5C Emulation Kit is installed, but the printer is in 
    the B/W mode or 4 × B/W mode. When you use the optional P5C 
    Emulation Kit, make sure that the printer is in the Color mode. 
    Invalid PS3
    The PostScript3 ROM module is broken. Turn off the printer and 
    contact your dealer.
    Invalid ROM A
    The printer cannot read the installed optional ROM module. Turn 
    off the printer, then remove the ROM module.
    Jam-Paper Size Error
    A paper jam occurred because the wrong size paper has been 
    loaded. Clear the jammed paper and set the paper size setting 
    correctly. See  Clearing Jammed Paper on page 345 to find how 
    to clear the jammed paper.
    Manual Feed ssss
    The manual feed mode is specified for the current print job. Make 
    sure the paper size indicated by ssss is loaded, then press the 
    NStart/Stop button.
    Mem Overflow
    The printer has insufficient memory to execute the current task. 
    Press the NStart/Stop button on the control panel to resume 
    printing, or press the +Cancel Job button to cancel the print job.
     
    						
    							270Using the Control Panel Menus Locked
    This message appears if you try to change the printer’s settings 
    through the control panel when the buttons are locked. You can 
    unlock them by using the Network utility. Refer to the Network 
    Guide for information.
    Need Memory
    The printer has insufficient memory to complete the current print 
    job. 
    To clear this error message, select Clear Warning from the control 
    panel’s Reset Menu. See How to access the control panel menus 
    on page 223 for instructions.
    To prevent this problem from happening again, add more 
    memory to your printer as described in  Memory modules on 
    page 414, or reduce the resolution of the image to be printed.
    NonGenuine Toner Cartridge
    The installed toner cartridge is not a genuine Epson product. 
    Installing a genuine toner cartridge is recommended. Using a 
    non-genuine toner cartridge may affect print quality. Epson shall 
    not be liable for any damages or problems arising from the use of 
    consumable products not manufactured or approved by Epson.
    Install a genuine Epson product, or Clear All Warnings of the 
    Reset Menu on the control panel to clear the warning message. 
    See  Toner Cartridge on page 315 for instructions on replacing 
    the imaging cartridge.
    NonGenuine Toner uuuu
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C2600N User Manual