Epson AcuLaser C2600N User Manual

							Using the Control Panel251
7
7
7
7
7
7
7
7
7
7
7
7
* Depending on whether Letter (62) or A4 (66) paper has been selected.
Font
Selects the font.
Pitch
Item Settings (default in bold)
FontCourier, Prestige, Roman, Sans Serif, Roman T, 
Orator S, Sans H, Script, OCR A, OCR B
Pitch10, 12, 15 cpi, Prop.
CondensedOff, On
T. Margin 0.40 ... 0.50 ... 1.50 inches in 0.05-inch 
increments
Text 1... 62/66*... 117lines
CGTablePcUSA, Italic, PcMultilin, PcPortugue, 
PcCanFrenc, PcNordic, PcTurkish2, 
PcIcelandic, PcE.Europe, BpBRASCII, 
BpAbicomp, Roman-8, PcEur858, ISO Latin1, 
8859-15ISO, PcSI437, PcTurkish1, 8859-9 ISO, 
Mazowia, CodeMJK, PcGk437, PcGk851, 
PcGk869, 8859-7 ISO, PcCy855, PcCy866, 
PcUkr866, PcLit771, Bulgarian, Hebrew7, 
Hebrew8, PcHe862, PcAr864, PcAr864Ara, 
PcAr720, PcLit774, Estonia, ISO Latin2, 
PcLat866
CountryUSA, France, Germany, UK, Denmark, 
Sweden, Italy, Spain1, Japan, Norway, 
Denmark2, Spain2, LatinAmeric, Korea, Legal
Auto CROn, Off
Auto LFOff, On
Bit ImageDark, Light, BarCode
ZeroChar0, (or the zero character with a slash)
 
						

							252Using the Control Panel Selects the pitch (the horizontal spacing) of the font in fixed pitch, 
measured in cpi (characters per inch). You can also choose 
proportional spacing.
Condensed
Turns condensed printing on or off.
T. Margin
Sets the distance from the top of the page to the baseline of the 
first printable line. The distance is measured in inches. The 
smaller the value, the closer the printable line is to the top.
Text
Sets the page length in lines. For this option, a line is assumed to 
be 1 pica (1/6 inch). If you change the Orientation, Page Size, or 
T. Margin settings, the page length setting automatically returns 
to the default for each paper size.
CG Table
Use the character generator (CG) table option to select the 
graphics character table or the italics table. The graphics table 
contains graphic characters for printing lines, corners, shaded 
areas, international characters, Greek characters, and 
mathematical symbols. If you select Italic, the upper half of the 
character table is defined as italic characters.
Country
Use this option to select one of the fifteen international symbol 
sets. See  International character sets on page 455 for samples of 
the characters in each country’s symbol set.
Auto CR
 
						

							Using the Control Panel253
7
7
7
7
7
7
7
7
7
7
7
7
Specifies whether the printer performs a 
carriage-return/line-feed (CR-LF) operation whenever the 
printing position goes beyond the right margin. If you select Off, 
the printer does not print any characters beyond the right margin 
and does not perform any line wrapping until it receives a 
carriage-return character. This function is handled automatically 
by most applications.
Auto LF
If you select Off, the printer does not send an automatic line-feed 
(LF) command with each carriage-return (CR). If On is selected, a 
line-feed command is sent with each carriage-return. Select On if 
your text lines overlap.
Bit Image
The printer is able to emulate the graphics densities set with the 
printer commands. If you select Dark, the bit image density is 
high, and if you select Light, the bit image density is low.
If you select BarCode, the printer converts bit images to bar codes 
by automatically filling in any vertical gaps between dots. This 
produces unbroken vertical lines that can be read by a bar code 
reader. This mode will reduce the size of the image being printed, 
and may also cause some distortion when printing bit image 
graphics.
ZeroChar
Specifies whether the printer prints a slashed or unslashed zero.
FX Menu
This menu allows you to make settings which affect the printer 
when it is in the FX emulation mode.
 
						

							254Using the Control Panel
* Depending on whether Letter (62) or A4 (66) paper has been selected.
Font
Selects the font.
Pitch
Selects the pitch (the horizontal spacing) of the font in fixed pitch, 
measured in cpi (characters per inch). You can also choose 
proportional spacing.
Condensed
Turns condensed printing on or off.
Item Settings (default in bold)
FontCourier, Prestige, Roman, Sans Serif, Script, 
Orator S, OCR A, OCR B
Pitch10, 12, 15 cpi, Prop. 
CondensedOff, On
T. Margin 0.40 ... 0.50 ... 1.50 inches in 0.05-inch 
increments
Text 1... 62/66*... 117lines
CGTablePcUSA, Italic, PcMultilin, PcPortugue, 
PcCanFrenc, PcNordic, PcTurkish2, 
PcIcelandic, PcE.Europe, BpBRASCII, 
BpAbicomp, Roman-8, PcEur858, ISO Latin1, 
8859-15ISO
CountryUSA, France, Germany, UK, Denmark, 
Sweden, Italy, Spain1, Japan, Norway, 
Denmark2, Spain2, LatinAmeric
Auto CROn, Off
Auto LFOff, On
Bit ImageDark, Light, BarCode
ZeroChar0, (or the zero character with a slash)
 
						

							Using the Control Panel255
7
7
7
7
7
7
7
7
7
7
7
7
T. Margin
Sets the distance from the top of the page to the baseline of the 
first printable line. The distance is measured in inches. The 
smaller the value, the closer the printable line is to the top.
Text
Sets the page length in lines. For this option, a line is assumed to 
be 1 pica (1/6 inch). If you change the Orientation, Page Size, or 
T. Margin settings, the page length setting automatically returns 
to the default for each paper size.
CG Table
Use the character generator (CG) table option to select the 
graphics character table or the italics table. The graphics table 
contains graphic characters for printing lines, corners, shaded 
areas, international characters, Greek characters, and 
mathematical symbols. If you select Italic, the upper half of the 
character table is defined as italic characters.
Country
Use this option to select one of the fifteen international symbol 
sets. See  International character sets on page 455 for samples of 
the characters in each country’s symbol set.
Auto CR
Specifies whether the printer performs a 
carriage-return/line-feed (CR-LF) operation whenever the 
printing position goes beyond the right margin. If you select Off, 
the printer does not print any characters beyond the right margin 
and does not perform any line wrapping until it receives a 
carriage-return character. This function is handled automatically 
by most applications.
Auto LF
 
						

							256Using the Control Panel If you select Off, the printer does not send an automatic line-feed 
(LF) command with each carriage-return (CR). If On is selected, a 
line-feed command is sent with each carriage-return. Select On if 
your text lines overlap.
Bit Image
The printer is able to emulate the graphics densities set with the 
printer commands. If you select Dark, the bit image density is 
high, and if you select Light, the bit image density is low.
If you select BarCode, the printer converts bit images to bar codes 
by automatically filling in any vertical gaps between dots. This 
produces unbroken vertical lines that can be read by a bar code 
reader. This mode will reduce the size of the image being printed, 
and may also cause some distortion when printing bit image 
graphics.
ZeroChar
Selects whether the printer prints a slashed or unslashed zero.
I239X Menu
The I239X mode emulates IBM® 2390/2391 Plus commands.
These settings are available only when the printer is in the I239X 
mode.
 
						

							Using the Control Panel257
7
7
7
7
7
7
7
7
7
7
7
7
*1Depends on whether Letter (63) or A4 (67) paper has been selected.
*2Depends on whether Letter (1) or A4 (2) paper has been selected.
Font
Selects the font.
Pitch
Selects the pitch (the horizontal spacing) of the font in fixed pitch, 
measured in cpi (characters per inch). You can also choose 
proportional spacing.
Code Page
Selects the character tables. Character tables contain the 
characters and symbols used by different languages. The printer 
prints text based on the selected character table.
T. Margin
Item Settings (default in bold)
FontCourier, Prestige, Gothic, Orator, Script, 
Presentor, Sans Serif
Pitch10, 12, 15, 17, 20, 24 cpi, Prop.
Code Page437, 850, 858, 860, 863, 865
T. Margin 0.30 ... 0.40 ...1.50 inches in 0.05-inch 
increments
Text 1 ... 63/67
*1... 117lines
Auto CROff, On
Auto LFOff, On
Alt. GraphicsOff, On
Bit ImageDark, Light
ZeroChar0, (or the zero character with a slash)
CharacterSet1
*2, 2*2
 
						

							258Using the Control Panel Sets the distance from the top of the page to the baseline of the 
first printable line. The distance is measured in inches. The 
smaller the value, the closer the printable line is to the top.
Text
Sets the page length in lines. For this option, a line is assumed to 
be 1 pica (1/6 inch). If you change the Orientation, Page Size, or 
T. Margin settings, the page length setting automatically returns 
to the default for each paper size.
Auto CR
Specifies whether the printer performs a 
carriage-return/line-feed (CR-LF) operation whenever the 
printing position goes beyond the right margin. If this setting is 
off, the printer does not print any characters beyond the right 
margin and does not perform any line wrapping until it receives 
a carriage-return character. This function is handled 
automatically by most applications.
Auto LF
If you select Off, the printer does not send an automatic line-feed 
(LF) command with each carriage-return (CR). If On is selected, a 
line-feed command is sent with each carriage-return. Select On if 
your text lines overlap.
Alt.Graphics
Turns the Alternate Graphics option on or off.
Bit Image
The printer is able to emulate the graphics densities set with the 
printer commands. If you select Dark, the bit image density is 
high, and if you select Light, the bit image density is low.
 
						

							Using the Control Panel259
7
7
7
7
7
7
7
7
7
7
7
7
If you select BarCode, the printer converts bit images to bar codes 
by automatically filling in any vertical gaps between dots. This 
produces unbroken vertical lines that can be read by a bar code 
reader. This mode will reduce the size of the image being printed, 
and may also cause some distortion when printing bit image 
graphics.
ZeroChar
Selects whether the printer prints a slashed or unslashed zero.
CharacterSet
Selects character table 1 or 2.
Support Menu
Enter the Support Mode by pressing the dDown button while 
turning the printer on, to make the Support Menu appears.
HDD format
Formats the Hard Disk Drive in the printer, if one is installed.
PS3 HDD Init
Initializes the Hard Disk Drive area where PostScript information 
is stored, if a Hard Disk Drive is installed.
Sleep Mode
Set the time after which the printer enters the sleep mode if the 
printer is not operated.
LCD Backlight
 
						

							260Using the Control Panel Set the LCD control setting. When Auto is selected, the printer 
controls the backlight of the LCD panel automatically. When the 
printer is in sleep mode, the backlight is off. When On is selected, 
the LCD backlight is always on.
Printer Adjust Menu
Enter the Support Mode by pressing the dDown button while 
turning the printer on, to make the Printer Adjust Menu appear.
Note:
This menu is a special function. You don’t have to change it for ordinary 
use.
Normal
Adjust the density for normal paper. The setting becomes darker 
as the value increases.
Normal Back
Item Settings (default in bold)
Normal -4 ... 0 ... 5
Normal Back -4 ... 0 ... 5
Thick -4 ... 0 ... 5
Trnsprnc -4 ... 0 ... 5
Envelope -4 ... 0 ... 5
Highland0 , 1
Feed Offset -3.5 ... 0.0 ... 3.5 mm
Scan Offset -3.5 ... 0.0 ... 3.5 mm
Feed Offset2 -3.5 ... 0.0 ... 3.5 mm
Scan Offset2 -3.5 ... 0.0 ... 3.5 mm