Comdial Executech 2000 Telephone System Instructions Manual

Station Programming
3.7.24 Group Call Pickup
Description:If a call rings to any station in a prearranged group, a user at another station in that group can dial a group
pickup code and answer the call. Assign the stations to call pickup groups using this procedure.
To Program:1.Dial 53 “STATION FEATURES”2. Dial 16 
“GRP. CALL PICKUP”
3.Dial 0 for no group
-OR-
4.Dial 1 - 4 for group 1 - 4 “GROUP X ”
5.Select station ports (LED On = Feature Assigned): Station 10 - 73, Dial 10 - 73 or press Cl0 - C73...

Station ProgrammingZMZ66-0683.7.30 Prime Line-Prime Group
And Prime Intercom
Description:If you assign a group of lines, an intercom line, or one individual line to a particular station for use as its
prime line, the station automatically selects that line for use when the user takes it off-hook.
To Program:1. Dial 53 “STATION FEATURES”
2.Dial 15 “PRIME LINE ”
3a.Assign prime line”PRIME LINE XX”
Line port 1-14 = Dial 01 - 14 or press Al - Al4
Line port 15, 16 = Dial 15,16 or press Bl, B2
Line port 17-24...

ZikiZ66-068Station Programming3.7.32 
Ringins Line Preference
; .,:: :
Description:When you assign this feature to a station, that station will automatically answer a ringing line when its user
takes it off-hook.
NOTE: Without Direct Ringing Assigned, Ringing Line Preference will notfunction.
To Program:1. Dial 53 ‘STATION FEATURES”
2.Dial 09 “RING LINE PREF. ”
3.Select station ports (LED On = Feature Selected): Station 10 - 73, Dial 10 - 73 or press Cl0 - C73
4.Dial +K for next station feature,
-OR-...

Station ProgrammingIMI66-0683.7.34 Subdued Off-Hook Voice Announce
(SOHVA) Groups
Description:Use this procedure to arrange station ports to originate and/or receive SOHVA calls by assigning them to
SOHVA calling groups.Also provide selective SOHVA calling to the system by arranging certain station
ports together into groups for SOHVA calling between one another.
To Program:1. Dial 53 “STATION FEATURES”
2. Dial 30 ‘SOHVA GROUP”
3.Dial 1 - 8 for group 1-8 “SOHVA GROUP X ”:4.Select all station ports to...

:IMZ66-068Station Programming
3.7.35 Service Observing
Description:You can give selected stations the capability to monitor, in an un-announced manner, an active call at
another station.
NOTE: Since this feature requires the executive override feature to function, the system automatically
enables executive override for the station when you enable servicing observing.You can also arrange
selected 
stations so that they cannot be serviced observed.
To Program:1.Dial 53 “STATION FEATURES’
2.Dial 10...

Station ProgrammingIMI66-068
3.7.37 Station Names
Description:You can assign individual names or category names to stations. These names will then be displayed by LCD
speakerphones when the speakerphones’ station is called by the named station. Typical names could be
TECH, MKT 1, J Smith.System attendants also have access to this station naming feature. You can
program all attendant level programming features with the base level entry 
ITCM % #
To Program:1.Dial 06 “‘STATION NAMES ”
2.Select station port...

._ZMZ66-0683.7.38 Station To Station Port Reassignment
Description:You can reassign the programming attributes from one station to a different station port with this
programming procedure (logical to physical reassignment). This feature allows you to automatically
exchange all software attributes for a station (logical assignment) connected at one station port with those
attributes assigned to a different station port without physically relocating the stations (physical
assignment) or reprogramming any...

Stuti4m ProgrammingIMIN-068
3.7.41 Station Con
ns”
guration - Button
Mapping ( on-Square System Configuration)
Description:You can assign (map) every programmable button at each station to be line select buttons that provide
access to outside lines, to be direct station select (DSS) buttons that provide quick access to system stations,
to be special purpose buttons that provide telephone users one-button access to features, or to be idle
buttons that provide autodial locations for the station user.
When...

ZMZ66-068Station Programming
3.7.41.1Account Code Button
:‘I..,
Description:Press the account code button and then dial an account code to record a call into a particular category
without interrupting the call.
To Program:1.Dial 56 “BUTTON MAPPING“
2. Dial 17 
“ASSIGNACCTKEY ”
3.Select button to be programmed: Press Al - A14, Bl - B3, or press 103-107 for B4-B8
or 122 for A15
4.Select station ports to be programmed: Station 10 - 73, Dial 10 - 73 or press Cl0 -C73
Dial +I+ for further ACCOUNT CODE button...

Station ProgrammingIA!fZ66-0683.7.41.3
Bhnk Buttons
Description:Blank those buttons that you want to be dynamic line buttons or autodial buttons.
NOTE:When blanking buttons, be sure a previously assigned button is idle fjieature not selected by user) before
you blank it.
To Program:1. Dial 56 ‘BUlTON MAPPING”2. Dial 04 
‘BLANK/AUTODIAL”
3.Select button to be programmed: Press Al - A14, Bl - B3, or press 103-107 for B4-BS
or 122 for Al5
4. Dial#
5.Select station ports to be programmed with this blank...