Comdial Executech 2000 Telephone System Instructions Manual

ZA!ZZ66-068ZnstaUution
2.13.6 Repair Authorization
FCC regulations do not permit repair of customer owned equipment by anyone except the manufacturer, their
authorized agent, or others who might be authorized by the FCC.However, routine repairs can be made according
to the maintenance instructions in this publication, provided that all FCC restrictions are obeyed.2.13.7 Radio Frequency Interference
The electronic key system contains incidental radio frequency generating circuitry and, if not installed...

IMI66-068System Records
Programming The System
‘-.‘.:.:
3.1Using This Chapter 3-l
3.2Understanding How To Program3-l
3.3Understanding System Programming 3-3
3.4Master Clearing And System Defaults 3-4
3.5Programming The System 3-6
3.5.1 Data Baud Rate 3-6
3.5.2 Do Not Disturb 3-7
3.5.3 Do Not Disturb Inhibit 3-7
3.5.4 Do Not Disturb Override 3-7
3.5.5 DTMF Dialing Feedback 3-8
3.5.6 Exclusive Hold 3-8
3.5.7 LCD Messaging 3-9
3.5.8 Music On Hold 3-10
3.5.9 Station Monitoring 3-10
3.5.10 Station...

System RecordsIMI66-068
3.6Programming The Lines 3-17
3.6.1Introduction 3-17
3.6.2Abandoned Hold Release3-18
3.6.3Automatic Privacy 3-18
3.6.4Automatic Privacy Release3-18
3.6.5Line Disable 3-19
3.6.6Line Groups 3-19
3.6.7Line Names 3-20
3.6.8Line Port Functions-Auxiliary Lines3-21
3.6.9Line Port Functions-C.O. Lines3-21
3.6.10Line to Line Port Reassignment3-21
3.6.11Pulse 
/ Tone Dialing-Pulse3-22
3.6.12Pulse 
/ Tone Dialing-Tone3-22
3.6.13Block Programming 3-23
3.6.14Block Programming Button3-23...

ZMZ66-068System Records
-. :,I. .:
3.8Account Codes 3-52
3.9Direct Department Calling3-56
3.10Direct Inward Station Dialing3-58
3.11Data Printer Service Configuration
3.12Execumail3-62
3.13Call Costing3-66
3.14
SMDA3-80
3.15Toll Restriction 3-84
3.16Cassette Tape Recorder Interface
3.17Programming Reference Chart3-90
3.7.29Prime Line / Prime Group 3-38
3.7.31Message Wait Originate 3-38
3.7.32Ringing Line Preference 3-39
3.7.33SOHVA Disable 3-39
3.7.34SOHVA Groups 3-40
3.7.35Service Observing 3-41...

IMZ66-068.:System Programming
Programming The System3.1 Using This Chapter
Programming the customer’s new system is the most intricate and important aspect of the installer’s job.The benefit
of the ExecuTech 2000 is that you can program every system differently to fit each customer’s individual needs.
Chapter 3 is divided into four programming sections: system lines, stations, and miscellaneous features, each of
which lists features in alphabetical order.
If you do not know where to find the feature you...

System ProgrammingIMIN-068
3.2.1Using Class of Service Programming
The installer performs the Class of Service Programming when the system is first installed. Any programming
function can be done under this type of programming.Class of service programming includes System, Station, and
Line programming. The password for COS programming is 
H/746%3.2.2 Using Administration Programming
Administrators can use administration programming to program all system features except line attributes and the
master...

ZMZ66-068System Programming
3.3 Understanding System Programming

System ProgrammingIiW66-068
3.4Master Clearing and System Defaults
You can return the entire programming configuration to the factory settings using the master clear procedure.You
can also return the individual system, line, and station class of service configurations to their factory settings using
the system, line, and station default procedures. The operating parameters and class of service values provided by the
factory settings will provide satisfactory performance in a broad range of site...

ZMZ66-068System Programming3.4.4 Defaulting The Stations
DescriptionReturns the station configuration features to factory settings.
To Program:1.Press ITCM Dial +k # 7 4 6 S “CONFZG. MODE”
2.Dial 50 “STATION DEFAULT ”
3.Dial 00 to default station ports system-wide,
-OR-
Select individual station port to be defaulted: Station 10 - 73, Dial 10 - 73 or press Cl0 - C73.
4.Dial % for next station to default,
-OR-
Dial %% + for configuration mode or SPKR to quit.3.4.5Defaulting Button Assignments...

System ProgrammingZMZ66-068
3.5 Programming The System
Programming the system means that you are setting the parameters that will be true system wide. If you are unsure
whether or not you are programming the correct function, check chapter 5, Description of System Features,in the
back of this manual for a full definition of the feature.You should make a record of all your programming
decisions-it will help you keep track of what you have done and will help you troubleshoot any problem that might
arise...