Comdial Dxp Plus Instructions Manual

lMl66-123DXP Plus Programming hstructionsSearch Type (Type of Hunting)
Description:
There are several distinct types of station hunting.Terminal Hunting
Terminal station hunting always delivers a call to the first idle station programmed in the hunt
group.If the station does not answer within a programmed amount of time (programmed as the
Call Advance Timer), the system delivers the call to the next sequential idle station
programmed in the hunt group. The system makes no attempt to balance the...

DXP Plus Programming InstructionslMl66-123Direct Ring
Description:Use this procedure to choose the line ports that you want to ring at a station hunt group as soon
as a 
calI appears. Direct ringing sounds during the day 1 and day 2 time periods but does notring during the night ringing mode or during the manual night transfer (of ringing) operation.
Programming:1~ Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, type item number for hunt groups...

lMl66-123DXP Pius Programming hstrwdionsDay 1 Ring
Descriptions
Use this procedure to choose the line ports that you want to ring at stations during the day 1
ringing mode time period.
Refer to the paragraph titled, 
Day 1, Day 2, and Night Ringing Begin
and End Times, 
to set the beginning and ending times of this ringing.Programming:
1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, type item number for hunt groups and press ENTER.
4. Type...

DXP Plus Programming InstructionslMl66-123
Night RingDescription:
Choose the line ports that you want to ring at stations during the night ringing mode of
operation. The ringing arrangement that you configure here is the arrangement that is active
both during the automatic night ringing time period and whenever the attendant manually
activates the night transfer (of ringing) operation. Do note that the attendant commanded night
ringing period supercedes the automatic night ringing period. Refer to the...

Queue Ringing Calls
Description:With this feature enabled, in the case of no answer or if all stations in the hunt group are busy,
hunt group calls wait in a queue for a station to become idle. The calls wait in queue until the
overflow timer times out. At timeout, the system routes the call to a designated overflow
destination. The overflow destination is an intercom number or feature code that calls another
station, a group intercom number, a voice mail number, or another station hunt group pilot...

DXP Plus Programming InstructionsIMltS-123Call Advance Time
Description:
This is the time interval that a station within a hunt group rings unanswered before the system
routes the call to the next station in the group. This timer is programmable from 10 seconds
through 5 minutes. The default value is 20 seconds.Programming:
1, Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, type item number for hunt groups and press ENTER.
4. Type number for hunt...

lM166-123DXP Plus Programming InstrwtionsRecall Time
Description:This is the maximum time interval that an unanswered transferred call hunts within a group
before recalling to the source of the transfer.This timer is programmable from 30 secondsthrough 15 minutes. The default value is 2 minutes.
Programming:
1 e Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, type item number for hunt groups and press ENTER.
4. Type number for hunt group (l-64)...

7.6.2Member List
Description:Use this procedure to add, remove, and insert stations in the hunt groups. A station hunt group
may contain all stations in the system but is limited to personal intercom numbers only. The
DXP 
Plus supports a maximum of 64 hunt groups.Each hunt group may include the maximum
number of stations that the system can support; however, due to system memory limitations, all
hunt groups may not contain all stations simultaneously. Since the system makes a total of 32
Kbytes of...

Programming Line Features
0 LineProgramming.....................8 .ll 
LineGroupProgramming.................8.2l Copy Model Line (Block Programming, Line)......
8.3l Direct Inward Dialing (DID) Support...........
8.4l 
GroundStartLineSupport................8.5l Loop Start Line Support..................
8.6l 
TieLineSupport......................8.7l Direct Inward System Access Programming . 
O s . e - . 8.8
Line Features Programming 8-l 

lM166-123BXP Plus Programming instructions
8.1Line Programming
8.1.1Line NameDescription:
You can assign a name to a line. A name shows in the display of an LCD speakerphone as a
identification aid. A valid name is composed of any seven alpha-numeric characters but the
first character must be an alphabetic character.Programming:
To assign a name to a line,
1. Press CONTROL T for main menu.
2. From main menu, select lines and press ENTER.
3. From lines menu, select line programming and press ENTER.
4....