Home > Comdial > Communications System > Comdial Dxp Plus Instructions Manual

Comdial Dxp Plus Instructions Manual

Here you can view all the pages of manual Comdial Dxp Plus Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 921

LOOD Start Line SumortDescription:The multipurpose line board provides system interface for loop start lines, ground start lines,
and E and M tie lines. These are typically the three different line types that the central office
(CO) makes available for connection to the public switched network. With the loop start line
type, the DXP Plus bridges a resistance across the tip and ring leads to signal the CO to
establish a communications link for an outgoing call. The CO detects the resulting current flow...

Page 922

IM166-123DXP Plus Programming hstruetions8.7
Pie Line Support
The multipurpose line board provides system interface for loop start lines, ground start lines, and E and M tie
lines. These are typically the three different line types that the central office (CO) makes available for connection
to the public switched network. The tie line connections (also known as tie trunk access) are special circuits that
allow, on either a dial-up or a continuous connection (hot line) basis, the DXP 
Plus to communicate...

Page 923

DXP Plus Programming Instructions/M/66-123Tie Line Non-Standard Protocol 
Signalling (Line Access)
Description:
You can program the system to respond to two types of non-standard tie line signalling
protocols. They are known 
as hot line and intercom dialing.
Hot Line: You can program the system for hot-line operation so that as soon as a user accesses
the tie line, the station or stations at the distant system that have access to the personal or group
intercom assigned to the hot line will ring. If you...

Page 924

Automatic Number Identification (ANI) Delivery
Description:
Automatic Number Identification (ANI) is a Tl service feature for both E&M and DID lines.
Long distance common carriers offer 
ANI as a feature to dial $00 and dial 900 lines. The ANI
feature provides information to an internal telephone system that identifies the telephone
number of the calling party. Businesses served by a dial 800 or dial 900 service allow any
available user to answer the calls and have their internal telephone system process...

Page 925

Call Announce
Description:This feature, when enabled, allows tie line callers from outside the system to voice announce
incoming calls to the DXP Plus station after they hear an alert tone. You must also arrange the
DXP Plus system to respond to voice announce intercom calls.
Programming:Refer to Section 8.7.2.
Dialing Mode
Description:Program the tie line to match either a DTMF tone or a rotary (pulse) dialing line as supplied by
the central office (CO).
Programming:Refer to Section 8.7.2.
Toll Groups...

Page 926

/M/66-123DXP Plws Programming hsfrwcfions
8.7.2Tie Line Support Programming
Programming:1.Press CONTROL T for main menu.
2.From the main menu, select lines and press ENTER.
3.From the lines menu, select line programming and press ENTER.
4.Type line port number l-240 or previously assigned name and press ENTER.
The system displays page 1 of the line programming menu
5.From line programming menu, type item number for line type and press ENTER.
6.Press SPACE bar to toggle line type and press ENTER.
7.From...

Page 927

DXP Plus Programming Instructions/M/66-123
8.8Direct Inward System Access (DISA) Programming
Through the DISA programming routines, you can configure a system to allow outside callers to call directly into
the system. DISA callers can dial authorization codes that allow them to use the system’s features that arenormally available only to inside callers.
NOTE: It is possible to use the automatic route selection (ARS) feature (Section 12) along with the DZSA feature
to route DZSA calls that pass through...

Page 928

/M/66-123DXP Plus Programming Instructions
8.8.2Enabling Or Disabling DISA LinesDescription:
Programming
Use the following programming instructions to enable or disable DISA capability on lines 1
through 240. Also, use the DISA Voice Options 1 through 4 to select digital voice announce
(DVA) messages. For example, selecting DISA voice option 2 will cause welcome greeting 2,
day main menu 2, night main menu 2, recall no answer 2, and recall busy 2 prompts to play
whenever a DISA line is covered by DVA....

Page 929

DXP Plus Programming Instructions/M/66-123
8.8.4Remote COS ProgrammingDescription:DISA callers that have assigned authorization codes have access to advanced system features.
The features that they have access to are controlled by the station class of service that you
assign with this programming procedure. The intercom number that is associated with this
remote COS assignment is the same intercom number that is associated with the caller’s DISA
authorization code that you set using the Section 8.8.3...

Page 930

DXP Plus Programming Instructions/M/66-123
Programming Intercom Numbers
o Understanding Station Numbering............9.1l Modifying Intercom Numbers...............
9.2l Adding Intercom Numbers................
9.3l Removing Intercom Numbers...............
9.4l Renumbering Intercom Numbers.............
9.5
3
AtoZ KELLATRONICS, INC,
Intercom Number Programming 9-1 
Start reading Comdial Dxp Plus Instructions Manual

Related Manuals for Comdial Dxp Plus Instructions Manual

All Comdial manuals