Home > Comdial > Communications System > Comdial Dxp Plus Instructions Manual

Comdial Dxp Plus Instructions Manual

Here you can view all the pages of manual Comdial Dxp Plus Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 871

/M/66-123DXP Plus Programming Insfrwetions
7.2.20Pick-L/x, Grcxms
Description.=Use this procedure to place a number of stations in a call pick-up group so that one station can
answer a call ringing at any other station in the group.Programming:
1 D Press CONTROL T for main menu.
2. From the main menu, select stations and press ENTER.
3. From the stations menu, select station programming and press ENTER.
4. Type personal intercom number or previously assigned name and press ENTER.
5. From station...

Page 872

7.2.22Single Line TAP (Single Line Proprietary Telephone TAP Button)Description:
Use this procedure to set the function of the TAP button on single line proprietary telephones.Programming:
1.Press CONTROL T for main menu.
2.From main menu, select station and press ENTER.
3.From station menu, select station programming and press ENTER.
4.Type personal intercom number or previously assigned name of station being programmed
and press ENTER.
5.From station programming menu, type item number for feature and...

Page 873

7.2.24Allow Ringer Off (Ringer Volume Off)
Description:On some proprietary telephones, the user selects the ringer volume level by pressing a
rocker-type volume control repeatedly to select one of four different volume levels. The lowest
volume setting is essentially an off condition as the telephone sounds only one low-volume ring
burst when a call rings the station.
Sometimes users would rather not receive even one ring burst. For these cases, program the
system so that it completely silences the...

Page 874

7.2.26Consoles Installed (DSS/BLF Consoles Installed)Description:Use this procedure to assign 
DSS/BLF consoles to a station and to identify the ports that the
consoles occupy.NOTE: Before you can assign a console and 
nume the console port with this programming step,
you must use the Section 7.4 programming procedure to identify the type of console and
the station port to which it is assigned.
Programming:
1.Press CONTROL T for main menu.
2.From main menu, select station and press ENTER.
3.From station...

Page 875

/M/66-123DXP Plus Programming hstructions
7.2.28Automatic Transfer On Busy
Description:You can enable automatic attendant transfer on busy for individual station ports if you wish.
With this feature enabled, the system will ring a busy telephone when the voice mail system is
attempting to transfer a call to it thus giving the user the option of leaving his or her present call
and taking the new one. With the feature disabled, the busy telephone is not signalled by the
presence of a new call and the voice...

Page 876

7.2.30A ttendan t Position (Alternate.Ovetflo w)Description:
The attendant position station provides incoming call direction, and controls system-wide
operating features. Additionally, the attendant position is responsible for certain programming
features. The system defaults two stations as attendant positions (logical station numbers 479
and 480) but it does not limit the number of attendant positions that it can support. Also refer to
Section 6.9.13.Programming:
1. Press CONTROL T for main menu.
2....

Page 877

lMl66-123DXP Plus Programming instructions
7.2.31Extended DTMF DialingDescription:
You can enable the extended DTMF length dialing feature on a per station basis with this
programming procedure. The system generates DTMF tones of extended length when users take
their telephones off-hook and then wait until after the system sounds the extended 
dialing tone
burst before they engage automatic dialing. This feature also allows an analog station to
generate extended DTMF tones when its user manually dial...

Page 878

Uvll66-123
7.2.32Softkeys Setup (Interactive Button SuppotfjDescription:The system provides support for interactive buttons on LCD 
LJTroduct codesof 
7010s and 7016s (all revisions), and 7700s (revision H P:interactive
buttons and the associated expanded displays provide quick, 
,_:I features and
straight-forward button programming without the need 
for 21..ult, the
interactive button support is disabled; therefore, you must 
tzk.JII to enable it.
When you enable them, the system overrides any previous...

Page 879

/M/66-323DXP Plus Programming hstructions
7.2.33/ST Hold Confirmation
Description:Industry-standard telephones sound a special hold confirmation tone when their users place
calls on hold. Prior to this software release, these telephones returned to intercom dial tone
when their users placed calls on hold. The system defaults with the special confirmation tone
enabled; however, you can disable the feature if you wish. The confirmation tone is three 80 ms.
on -80 ms. off tone bursts repeated at 800 ms....

Page 880

DXP Plus Programming Instructions/M/66-123
7.2.35Industry-Standard Telephone Support
The DXP plus digital communications system supports the use of industry-standard telephones.It does this
through the use of industry-standard telephone station interface circuit boards and a DXRNG ring generator
assembly.Refer to the Comdial publication 
IMI89-184, Installing An Industry-Standard Telephone Station
Board 
In The DXP Plus Digital Communications System, for installation details. Program the DXP Plus system...
Start reading Comdial Dxp Plus Instructions Manual

Related Manuals for Comdial Dxp Plus Instructions Manual

All Comdial manuals