Home > Comdial > Communications System > Comdial Dxp Plus Instructions Manual

Comdial Dxp Plus Instructions Manual

Here you can view all the pages of manual Comdial Dxp Plus Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 851

/M/66-123DXP Pius Programming instructions
7.1.42Clear Major Alarm RingDescription:
This feature allows users to clear the major alarm ring condition from a telephone station. To
make this feature available to users, you must first program a class of service as described
below and then assign that class of service to the user’s telelphone station.Programming:
1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER....

Page 852

DXP Plus Programming InstructionsIMl66-123
7.1.44Restrict A RS Hookflash
(Automatic Route Selection, Hookflash Restriction)
Description:This feature enhances ARS response to hookflash action on an outside line when that action is
followed by dialed digits. With the feature enabled, the system delays response to a hookswitch
flash until after the ARS feature verifies as valid all subsequent dialed digits. With the feature
disabled, the system sends the hookflash over the line without waiting for the ARS...

Page 853

/M/66-123DXP Plus Programming lnsfrucfisns
7.1‘46Enhanced LCD Display
Description:Take this programming action to enhance the display of an LCD-equipped telephone so that it
shows both the name of the calling station and its personal intercom number.Programming: 1 D
2.
3.
4.
5.
6.
-7.
8.
9.
Press CONTROL T for main menu
From main menu, select stations and press ENTER.
From stations menu, select COS programming and press ENTER.
Type class of service number (l-32) that corresponds with class of service...

Page 854

DXP Plus Programming instructions
7.2Programming Station Features
lMl66-123
7.2.1Personal lnfercom Number
Description:Use this programming procedure to change the station’s personal intercom number.
Also refer to 
Section 9. I.
Programming:
1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4. Type personal intercom number or previously assigned name and press ENTER.
5. From station programming menu,...

Page 855

/M/66-123BXP Pius Programming Instructions
7.2.3Class Of ServiceDescription:
Programming:
You can assign a group of preprogrammed class of service station features to a station. The
system makes up to 32 different classes of service available, and you can program the feature
values differently in each one.
1~ Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4.Type personal intercom number or previously...

Page 856

DXP Plus Programming instructionsIMB-123
7.2.5Idle Line PrioritvDescription:
If you use Section 7.1.14 to give a station the ability to automatically connect to an idle assigned
line when the user takes the handset off-hook, take this programming action to set the priority in
which the system chooses the idle lines for use. You can place up to eight lines in this prioritylist.
Programming:
1 0 Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select...

Page 857

7.2.7Group Intercom Access
Description:Use this procedure to add group intercom numbers to stations for their use. Also refer to
Section 7.3 to map buttons for group intercom number selection. See Section 9 for other
intercom number considerations.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select station and press ENTER.
3. From station menu, select station programming and press ENTER.
4. Type personal intercom number or previously assigned name of station being programmed
and...

Page 858

DXP Plus Programming InstructionsIMIH-123
7.2.8Prime Line Programming
Prime Line TypeDescription:
When you enable this feature, the station automatically selects a line, line group, or intercom
number for use when the station user takes the station off hook. Use the programming
procedures shown below to select the line port, line group, or intercom number to serve as theprime station calling interface.
NOTE: You can create an intercom hot line telephone by taking special programming action
when you...

Page 859

/M/66-723DXP PIUS Pfogramming Instrwctions
Prime Line Group
Description:Use this procedure to choose the prime line group.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4. Type personal intercom number or station name and press ENTER.
5. From station programming menu, select prime line group and press ENTER.
6. From prime line group menu, type 1-16 and press ENTER.
7. When finished,...

Page 860

DXP Plus Programming InstructionslMl66-123
7.2.9Tone Or Voice Signalling (Tone First)Description:
Intercom calls are either tone or voice signalled as a first choice with the other mode available
as a second choice. Use this procedure to select the first choice in intercom signalling on a per
station basis.Programming:
1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4.Type personal intercom number or...
Start reading Comdial Dxp Plus Instructions Manual

Related Manuals for Comdial Dxp Plus Instructions Manual

All Comdial manuals