Comdial Dxp Plus Instructions Manual

6.10Paging Programming (Paging Zones)
6.10.1Zone Programming
(Zone Names, Transmit Stations, Receive Stations)Description:
Use this programming procedure to arrange stations to transmit and receive voice
announcements, to and from a particular group of stations or to all stations in the system. Also
use this procedure to assign names to paging zones when a site requires named zones.Programming:
To place stations in paging zones and name the zones, use the following procedure.
1.Press CONTROL T for main...

/M/66-123DXP Plus Programming Instructions
6.10.3Paging TransmitDescription:
Use this procedure to give a class of service of stations the ability to transmit voice
announcements to one or all other station monitor speakers. Also refer to Section 
6.10.2.Programming:
1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From the COS programming menu,...

6.70.6Relays (External Paging Equipment Control)Description:
If your installer connects customer-supplied external paging equipment to the system’s external
paging port and that equipment requires external control, use this programming procedure to
assign a relay to control the paging equipment. Also refer to Section 6.10.9.Programming:
1.Press CONTROL T for main menu.
2.From main menu, select system and press ENTER.
3.From systems menu, select paging zones and press ENTER.
4.From paging zones menu,...

6.10.8Common Audible Ringer (Common Audible Ringer Inferface)Description:
If your installer connects customer-supplied external paging equipment to the system’s external
paging port, use this programming procedure to arrange for that 
equipment to sound the ring
signal 
of any or all lines.
You can arrange for it to track the ringing of the direct, delayed, day
1, day 2, or night ringing modes. Upon hearing the ringing over the external paging equipment,
the user can dial feature codes to answer the call...

DXP Plus Programming Instructions
6.11Change Password (Password Programming)
lM166-123
You can use this programming procedure to change the program entry password for both the installer and the
administrator and change the main programming station entry code for the 
system manager and the attendant.
The default sequence for both the installer and the administrator password entries is:I %746 %.
You can change part or all of either or both of these passwords to a customized sequence of up to 15 digits...

/M/66-123DXP Plus Programming Instructions
6.11.1Changing The Password
Description:To change the password, follow this procedure.
Programming1~ Press CONTROL T for main menu.
2. From main menu, select system and press ENTER.
3. From system menu, select change password and press ENTER.
4. Type a for administrator, 
i for installer, or s for station and press ENTER.
5. Type the current password and press ENTER.
6. Type the new password and press ENTER.
7. Retype the new password and press ENTER.
8. Repeat...

DXP Plus Programming InstructionslMl66-123
6.12Feature Renumbering
Description:Dialing codes for user features are flexible so that you can renumber them. This may be
necessary if site requirements dictate that personal or group intercom numbers fall within a
certain block or sequence. Since new number assignments can not conflict with existing
number, the system provides a block of unassigned numbers that you can use for renumber
assignment. At default, the system assigns blocks of numbers in the...

6.13Programming The T&-El ParametersDescription:
When the system is using the Tl--El option, you can program status and alarm alerting
parameters.Also, you can program the DXP 
Plus loss insertion that affects audio levels in theindividual Tl--El channels. The specific programming instructions for the Tl--El parameters
are shown int the followign list:
lenable Tl--El status reporting and major alarm alerting,
0program status log parameters,
0program major alarm alerting parameters,
lassign system status...

DXP Plus Programming Instructions/M/66-123
6.13.2Programming The T&-El Siatus Log ParametersDescription:
Use the following instructions to program the Tl--El status log parameters.Programming:
1.Press CONTROL T to return to main menu.
2.From main menu, select system and press ENTER.
3.From the system menu, select Tl--El status log parameters and press ENTER.
4.From the Tl--El status log parameters menu, select the row number for the
error type you want to program.The cursor will move to the threshold...

/M/66-123DXP Pius Programming Instructions
6.13.4Assigning A System Status Button To A Station
Description:Use the following instructions to program a system status button
Programming:1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select button mapping and press ENTER.
4.Type prime intercom number or previously assigned name and press ENTER.
(Screen presents current button map for review.)
5.Type first level button code (Ll-L25,0-9) and press...