Home > Comdial > Communications System > Comdial Dxp Plus Instructions Manual

Comdial Dxp Plus Instructions Manual

Here you can view all the pages of manual Comdial Dxp Plus Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 791

DXP Plus Programming InstructionslMl66-1236.7
System Clock (Time and Date)Description:The system clock provides time and date information for display on LCD speakerphones and for
SMDRBMDA timing and reporting. You must set the correct time and date to allow the system
to operate properly.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select system and press ENTER.
3. From system menu, type item number for feature and press ENTER.
4. Type time in 24 hour format 
(hhxnm) using leading...

Page 792

6.8.3Camp-On ToneDescription:
Use this procedure to set the duration of the camp-on tone that the system sends to a busy
station. Also refer to Section 
7.1.10.Programming:
1. Press CONTROL T for main menu.
2. Form main menu, select system and press ENTER.
3. From system menu, select timing and press ENTER.
4.From the system timing menu, type item number for feature and press ENTER.
5. Press SPACE bar for feature setting and press ENTER to accept setting.
6. When finished, press ESCAPE twice.
7. Type y...

Page 793

DXP Plus Programming lnsfructions/M/66-123
6.8.5Timed Recall (Held And Transferred Calls)
Attendant Hold RecallDescription:After a call has been on hold at an attendant station for a programmed length of time, the call
recalls to the attendant station. Use this procedure to set the amount of time before a held call
recalls at an attendant station.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select system and press ENTER.
3. From system menu, select timing and press ENTER
4. From...

Page 794

/M/66-123DXP Plus Programming Instructions
6.8.6Paging Access
Description:If you have assigned a paging zone and given that zone access to external paging equipment
(Section 6.101) plus enabled paging transmit capability (see Section 6.10.3) at a station, that
station has access to external paging equipment. With this paging access procedure, you can set
the maximum length of time that a station can stay connected to the external paging equipment.
This timing setting also controls the amount of time a...

Page 795

DXP Plus Programming Instructions/M/66-123
6.8.9Periodic Tone TimeDescription:After you enable the periodic warning tones that remind users to keep conversations short on
certain outside lines (Section 
7.1.33), use this procedure to set how often that you wish the
periodic warning tones to occur
Programming:1. Press CONTROL T for main menu.
2. From main menu, select systems and press ENTER.
3. From system menu, select timing and press ENTER.
4. From system timing menu, type item number for feature and...

Page 796

/M/66-123BXP Plus Programming Instructions
6.8.12Line-To-Line Connect Duration
Description:After you have given a station the ability to set up an unsupervised conference between two
lines (Section 
ZI.37), you should use this procedure to set the maximum amount of time that an
unsupervised conference can continue between two lines. When the time out occurs, the system
recalls the station from where the user enabled the unsupervised conference.
Programming:1~ Press CONTROL T for main menu.
2. From main...

Page 797

6.8.15Authorization Code TimeoutDescription:
Use the Section IO.5 procedure to enable the authorization code feature. Once a user uses the
authorization code to access his or her telephone features, those features remain in effect until
any idle time at the telephone exceeds the authorization code time-out period that you program
with this feature.Programming:
1. Press CONTROL T for main menu.
2. From main menu, select system and press ENTER.
3. From system menu, select timing and press ENTER.
4. From...

Page 798

/M/66-123DXP Plus Programming Instructions
6.8.18/ST Flash TimeDescription:
Programming:
You can program the timed length of the signal that results when a user of an industry-standard
telephone presses and releases the telephone hookswitch (or presses the TAP button if available
on his or her telephone) on a system-wide basis. Often, a signal with a short time length
(typically 500-750 ms) serves to alert the system to receive a feature code (flash) while a signal
with a long time length (typically...

Page 799

6.8.20Pulse Dial lnterdiait TimeDescription:
You can set the interdigit time between dial pulses when the system pulse-dials a number over a
line. The DXP 
Plus defaults this time to 150 msec. and provides a range of timing values
between 100 msec. and one sec. that you can set in either 50 or 100 msec. increments. Refer to
Section 8.1.9 to enable pulse dialing.Programming:
1. Press CONTROL T for main menu,
2. From main menu, select system and press ENTER.
3. From the system menu, select timing and press...

Page 800

/M/66-123DXP Pius Programming Instructions
6.9Svsfem Parameters
6.9. ISvnchronized Rinuin~Description:
The system can provide an audible distinction between internal and external call ringing when
needed. Enable or disable that feature with this programming procedure. When you enable this
feature, line call ringing sounds the same 
cadience as intercom calls. This feature does not apply
to direct inward dial lines (Section 8.4) and E&M lines (Section 
8.7)*Programming:
1 s Press CONTROL T for main menu....
Start reading Comdial Dxp Plus Instructions Manual

Related Manuals for Comdial Dxp Plus Instructions Manual

All Comdial manuals