Home > Comdial > Communications System > Comdial Dxp Plus Instructions Manual

Comdial Dxp Plus Instructions Manual

Here you can view all the pages of manual Comdial Dxp Plus Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 881

lMl66-123DXP Pius Programming InstructionsIST DTMF Receiver Timeout
Description:You can program the amount of time that the system waits to receive a DTMF tone from an
industry-standard telephone, after the user has lifted the telephone’s handset and before he or
she has pressed a dial pad digit, on a system-wide basis. The system disconnects the telephone
after this time-out occurs. If this happens, the user must hang up the handset and lift it again to
re-establish the dial tone.
Programming:1. Press...

Page 882

DXP Plus Programming Instructions/M/66-123
IST Flash Time
Description:You can program, on a system-wide basis, the timed length of the signal that results when a user
of an industry-standard telephone presses and releases the telephone hookswitch (or presses the
TAP button if available on his or her telephone).Often, a signal with a short time length
(typically 
5OG750 ms) serves to alert the system to receive a feature code (flash) while a signal
with a long time length (typically 1.5-2.0 
set) serves...

Page 883

IM166-123DXP Plus Programming hstructions
IST Ringing On Busy
Description:You can program industry-standard telephones to provide a ringing on busy signal to users.
With this feature, when an IST telephone is busy on a call and another call comes to that
telephone, the system sounds three quick tone bursts in the telephone’s handset receiver. If a
user does not wish to hear the ringing on busy tones while he or she is busy on a call, you can
take this programming action to eliminate it.
Programming:1....

Page 884

DXP Plus Programming Instructions/M/66-123
IST Ringing Patterns
Description:You can program the ringing pattern for either IST ring mode one or IST ring mode two. Mode
one causes a two-second ring phase while mode two causes a shorter one second ring phase.
For this feature to function properly, insure that the industry-standard telephone interface board
contains firmware revision 2C or higher
Programming:
1.Press CONTROL T for main menu.
2.From main menu, select system and press ENTER.
3.From system...

Page 885

iMl66-123DXP Plus Programming Instructions
7.3Button Mapping By Station (Square/Non-Square System)
Description:
Programming:The system assigns certain functions to each of the station buttons as a default condition.
Re-assign the button functions with this programming feature. You can assign functions at a
first level or at a second level at each button Assign functions at the first level that require
status light feedback because the system does not provide status light feedback to buttons at the
second...

Page 886

7.3.1Feature Mnemonic List
ACCT
ALTRN
ANSWER
APACE
ARD
ARECD
ARING
AUTH
BOTH
CAMP
CID
DND
DPKUP
DSTAT
EXOVR
FEATR
FWD-A
FWD-P
FWDRA
FWDRP
GPLSN
GPKUP
HDST
HOLD
ITCM
I####
LCDMS
LNG##
LN###
LOCK
MMEPG
MSGWT
MUSC#
NIGHT
OAI##OVERFL
PAGE#
PARK#PRVCY
QUEUERLSE
RSPW
S-OBS
SAVE
SDIAL
SILNT
SOHVA
SPLIT
SRIAL
SYSST
TAFS#
TBUSY
TRACK
VABLK
VOLSV
XVM##(account code button): allows users to enter an 
accent code
(alternate attendant button): places station in alternate attendant mode
(answer button): answers a...

Page 887

/M/66-123DXP Pius Programming fnnstructions
7.4Phone Types (Telephone Types)Description:
This programming feature allows you to identify the particular type of system telephone
equipment that you or your installer will connect to each station port.
You can also mark the station port equipment as undefined so that the system will not test the
port for a specific type of equipment and will not include the port in any menu presentations.
Also refer to 
Section 7.2.25 for the procedure for disabling a...

Page 888

7.5Copy Model COS, Station, Button Map (Block Programming)
7.5.1Block Programming, Class-Of-ServiceDescription:Program some or all class-of-service categories to match the programming of a model
class-of-service category.
Programming;
1 0Press CONTROL T for main menu.
2. From the main menu, select stations and press ENTER.
3. From the station menu, type item number for feature and press ENTER.
4. Select model COS by typing COS number l-32 for source COS and press ENTER.
5. Type COS numbers of destination...

Page 889

lMl66-123DXP Plus Programming Instructions
7.6Station HuntingDescription:
Station hunting is a feature that becomes available to DXP Plus users with software revision
3.A and later. 
Station hunting is a means of routing both intercom and outside calls through an
installer-determined logical grouping of stations and on to a designated ovefflow location in
case of no answer or if all stations in the hunt group are busy. To configure station hunting, you
must program the following parameters:
Options:...

Page 890

DXP Plus Programming InstructionslMl66-123
NameDescription:
The hunt group’s name is the seven character alpha-numeric name of this group that is used for
LCD display and reference.Programming:
1~ Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, type item number for hunt groups and press ENTER.
4. Type number for hunt group (l-64) and press ENTER.
5. For new hunt groups, type pilot number for hunt group.
6. Type item number for options, and press...
Start reading Comdial Dxp Plus Instructions Manual

Related Manuals for Comdial Dxp Plus Instructions Manual

All Comdial manuals