Canon Lbp 3200 User Guide

							Printing on Custom Paper2-44
Loading and Delivering Paper
2
3From [Output Size], select the name (size) of the set custom 
paper as needed.
If the size of a document is the same as that of paper (custom paper name) set in 
the manual feed slot, select [Match Page Size].
IMPORTANT
If the settings are different between [Page Size] and [Output Size], the printer 
produces an enlarged or reduced print automatically.
4From [Paper Type], select the type of paper that you set.
Select [Plain Paper] for using plain paper, [Heavy Paper] for heavy paper.
NOTE
•If paper curls excessively when printed with [Plain Paper] selected, select [Plain 
Paper L].
•If print fixing is not sufficient when printed with [Heavy Paper] selected, select 
[Heavy Paper H].
 
						

							Printing on Custom Paper2-45
Loading and Delivering Paper
2
5Click [OK] to close the [Properties] dialog box.
6Click [OK] to start printing.
 
						

							Printing on Custom Paper2-46
Loading and Delivering Paper
2
 
						

							CHAPTER
3-1
3
Setting Up the Printing 
Environment
This chapter describes the procedure for installing the printer driver in a computer and 
specifying the settings when using this printer in a network environment.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
After Installing the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Steps for Printing to be Followed Each Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Required System Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Installing the CAPT Software  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
For Windows 98/Me  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
For Windows 2000  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
For Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22
After Completing Installation (Canon LBP3200 Group)  . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Printing a Test Page  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
Using the Printer on a Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35
Setting the Print Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-36
Installation on the Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-45
Uninstalling the CAPT Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-49
 
						

							Introduction3-2
Setting Up the Printing Environment
3
Introduction
After Installing the Printer
The following shows work that should be performed after installing the printer.
■Installing the printer driver (See p. 3-4.)
The printer driver is software required for printing from an application you use. Specify the 
print settings in the printer driver.
■Setting a network environment (See p. 3-35.)
If you operate this printer in a network using the computers sharing function, you must 
specify the settings for the computer and install the printer driver in the client computers.
Steps for Printing to be Followed Each Time
The following shows the work that should be performed each time you print.
■Specifying printing preferences
Specify the paper size, document size, and print copies in the printer driver. If you do not 
specify these printing preferences properly, you may not obtain an accurate print.
■Performing a print job
Select the print menu from the application. This procedure differs depending on the 
application you use. See the instruction manual supplied with your application.
Required System Environment
The following system environment is required to use the printer driver.
■Operating system software environment
•Microsoft Windows 98/Me
•Microsoft Windows 2000 Server/Professional
•Microsoft Windows XP Professional/Home Edition
 
						

							Introduction3-3
Setting Up the Printing Environment
3
-System Requirements (minimum required)
*As the amount of memory that can be actually used differs depending on the system configuration of your 
computer or your application, the above environment does not guarantee printing in any case.
-System Requirements (recommended)
■Interface Environment
•USB:USB Full-Speed (USB1.1 equivalent)
NOTE
When using Sound, a PC synthesizer (and the driver for PCM synthesizer) must be 
installed in your computer. Do not use a PC Speaker driver (such as speaker.drv).
CPU
Memory (RAM)*
Hard Disk
(PC/AT compatibles)
Windows 98/MeWindows 2000/XP
PentiumII 300 MHz or higher PentiumII 300 MHz or higher
64 MB or more 128 MB or more
15 MB or more 15 MB or more
CPU
Memory (RAM)
Windows 98/MeWindows 2000/XP
PentiumIII 600 MHz or higher PentiumIII 600 MHz or higher
128 MB or more 256 MB or more
 
						

							Installing the CAPT Software3-4
Setting Up the Printing Environment
3
Installing the CAPT Software
This section describes the procedure for installing the CAPT software when 
connecting this printer to your computer directly.
IMPORTANT
•The CAPT software is required for printing with this printer. Be sure to install the CAPT 
software.
•When there is not enough free hard disk space, the dialog box shown below appears 
during installation.
In this case, click [OK] to stop the installation and increase the free space, then install the 
CAPT software again.
NOTE
When using this printer in a network, see Using the Printer on a Network, on p. 3-35.
For Windows 98/Me
NOTE
The screen shots used in this section are from Windows Me.
Installing from the CD-ROM
1Make sure that the power switch is turned OFF.
IMPORTANT
Do not turn ON the printer until Step 10 during installation procedure.
 
						

							Installing the CAPT Software3-5
Setting Up the Printing Environment
3
2Connect the printer to the computer with the USB cable.
3Turn ON the computer and start up Windows 98/Me.
4Put the supplied User Software for LBP3200 CD-ROM into 
the CD-ROM drive.
If the CD-ROM is already set in the drive, take it out and put it into again.
The CD-ROM menu will appear automatically.
NOTE
If the CD-ROM menu does not appear automatically, select [Run] under the [Start] 
menu, enter D:\English\CAP4MNU.exe, and click [OK]. (The CD-ROM drive 
name is indicated as D: in this manual. The CD-ROM drive name may differ 
depending on the computer being used.)
5Click [Install a Printer Driver].
The dialog box for confirming the language will appear.
 
						

							Installing the CAPT Software3-6
Setting Up the Printing Environment
3
6Confirm the language and click [OK].
After the preparation for installation is completed, the CAPT (Canon Advanced 
Printing Technology) software installer will start up.
The [Welcome] dialog box will appear.
7Click [Next].
The [Software License Agreement] dialog box will appear.
8Confirm the contents of the software license agreement, then 
click [Yes].
 
						

							Installing the CAPT Software3-7
Setting Up the Printing Environment
3
9Select [Automatic Detection (recommend)] and click [Next].
10Click [OK], then press   of the power switch to turn ON the 
printer.
Installation of the printer driver and the USB class driver will start automatically.
11After the installation is completed, click [OK].
The installation of the USB class driver and the printer driver is completed.
ON
OFF