Brother Hl 3260n User Manual

							REGULATIONS
xvii
Disconnect Device
This printer must be installed near a power outlet that is easily
accessible. In case of emergencies, you must disconnect the power
cord from the power outlet to shut off the power completely.
Geräuschemission / Acoustic Noise Emission (For Germany Only)
Lpa < 70dB (A) DIN 45635-19-01-KL2
Wiring Information (For U.K. only)
Important
If the mains plug supplied with this printer is not suitable for your
socket outlet, remove the plug from the mains cord and fit an
appropriate three pin plug. If the replacement plug is intended to take a
fuse then fit the same rating fuse as the original.
If a moulded plug is severed from the mains cord then it should be
destroyed because a plug with cut wires is dangerous if engaged in a
live socket outlet. Do not leave it where a child might find it!
In the event of replacing the plug fuse, fit a fuse approved by ASTA to
BS1362 with the same rating as the original fuse.
Always replace the fuse cover. Never use a plug with the cover omitted.
WARNING  - THIS PRINTER MUST BE EARTHED
 
						

							USER’S GUIDE
xviii
The wires in the mains cord are colored in accordance with the
following code :
GREEN AND YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
The colors of the wires in the mains lead of this printer may not
correspond with the colored markings identifying the terminals in your
plug.
If you need to fit a different plug, proceed as follows.
Remove a length of the cord outer sheath, taking care not to damage
the colored insulation of the wires inside.
 
						

							REGULATIONS
xix
Cut each of the three wires to the appropriate length. If the
construction of the plug permits, leave the green and yellow wire
longer than the others so that, in the event that the cord is pulled out of
the plug, the green and yellow wire will be the last to disconnect.
Remove a short section of the colored insulation to expose the wires.
The wire which is colored green and yellow must be connected to the
terminal in the plug which is marked with the letter “E” or by the safety
earth symbol 
 , or colored green or green and yellow.
The wire which is colored blue must be connected to the terminal
which is marked with the letter “N” or colored black or blue.
The wire which is colored brown must be connected to the terminal
which is marked with the letter “L” or colored red or brown.
The outer sheath of the cord must be secured inside the plug. The
colored wires should not hang out of the plug.
 
						

							CHAPTER 1 ABOUT THIS PRINTER
1 
1C
C
H
H
A
A
P
P
T
T
E
E
R
R
 
 
1
1
A
A
B
B
O
O
U
U
T
T
 
 
T
T
H
H
I
I
S
S
 
 
P
P
R
R
I
I
N
N
T
T
E
E
R
R
 
						

							CHAPTER 1 ABOUT THIS PRINTER
1-1
W W
h h
a a
t t
   
i i
s s
   
i i
n n
c c
l l
u u
d d
e e
d d
   
i i
n n
   
t t
h h
e e
   
C C
a a
r r
t t
o o
n n
C C
o o
m m
p p
o o
n n
e e
n n
t t
s s
When you unpack the printer, check to see that you have all of the following
parts:
1.  Printer
2.  Toner  (in the standard tray)
3. Drum  (pre-installed)
4. CD-ROM*
5. AC power cord*
6. Documents*
7. Tray number seal
*These parts are in the Localization kit in Europe.
Fig. 1-1
✒  Note
You may have additional parts that are not listed above depending on the
country where you purchased the printer.
1
3
2
45
6
7
 
						

							1-2
✒  Note
Parallel Interface Cable
• An interface cable is not supplied as standard. Please purchase an
appropriate cable according to the interface you intend to use. The power
cord may differ slightly from this figure depending on the country where
you purchased the printer.
• For parallel connections, an IEEE 1284 bi-directional parallel cable is
recommended. Most parallel cables support bi-directional
communication, but some might have an incompatible pin assignment or
may not be IEEE 1284 compliant.
• Do not use a parallel cable that is longer than 3 meters (10 feet).
 
						

							CHAPTER 1 ABOUT THIS PRINTER
1-3
! What is on the CD-ROM
Fig. 1-2
 
						

							1-4
1 Install software
For all users•  Printer driver (For more information,  see Chapter 2)
•   Automatic e-mail printing (For more information,  see Chapter 2)
For administrators •  BRAdmin Professional
•   Network Printer Driver Wizard
•   Network Print Software
•   Storage Manager
•   Analysis Tool Software
2Manual
•  User ’s guide
•   Network Guide
•   Technical Reviewer ’s Guide
These guides are in PDF format.
3 Brother Solutions Center
Introduction to our user support web page. You can easily access it and
receive the latest drivers and information for this printer.
4 Maintenance Tutorial
See the maintenance videos for this printer. We recommend that you view
the videos before getting started.
5 Make Disk sets
Copy the contents of the CD-ROM to floppy disks if you do not have a CD-
ROM drive.
 
						

							CHAPTER 1 ABOUT THIS PRINTER
1-5
!  What is on the CD-ROM for Macintosh users
Fig. 1-3
1 Maintenance Tutorial
See the maintenance videos for this printer. We recommend that you look at
the video first before getting started.
2 BR-Script PPD Installer
•Printer driver (For more information,  see Chapter 2)
This printer supports with Mac OS 8.0, and 9.0 versions.
3 Manual
•  User’s guide
•  Network Guide
•   Technical Reviewer’s Guide
These guides are in PDF format.
4 Brother Solutions Center
Introduction to our user support web page. You can easily access it and
receive the latest drivers and information for this printer.
5 Readme
6 Screen Fonts
When you use BR-Script 3 (PostScript level 3 language emulation), you can
use Agfa PostScript Fonts. We recommend that you install these fonts.
2
1
4
3
56
 
						

							1-6
   
G G
e e
n n
e e
r r
a a
l l
   
v v
i i
e e
w w
6
54
7
8
9
1
2
3
Fig. 1-4
1 Parallel interface port
2 Network interface port
3 CompactFlash slot (for optional memory expansion)
4 Output tray
5 Power switch
6 Upper right cover
7 Control panel
8 Front cover
9 Paper tray