Brother Hl 3260n User Manual
Have a look at the manual Brother Hl 3260n User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 5 MAINTENANCE
5-3
! Replacing the Toner bottle
✒
✒✒ ✒ Note
• If the “Toner empty” message does not disappear after replacing
the Toner bottle, follow these instructions:
- Confirm the printer power is on.
- Leave the Front cover open for more than 10 seconds.
- Close the Front cover.
Follow these steps to change the toner bottle:
☛
☛☛ ☛ 1.Open the Front cover.
ZAET010E
Fig. 5-2
☛
☛☛ ☛ 2.Lift the green handle.
ZAET020E
Fig. 5-3
☛
☛☛ ☛ 3.While pushing the green lever downwards (), use the green handle to
slide the Toner holder out slightly ().
ZAET021E
Fig. 5-4
5-4 ☛ ☛☛ ☛ 4.Release the green lever and then continue to gently slide the Toner holder out until it stops. !Caution • If you continue to push the green lever down while you continue to slide the Toner holder out, the toner holder may fall out. Fig. 5-5 ☛ ☛☛ ☛ 5.Push the Toner bottle backwards slightly () until you can lift the top of the bottle upwards () and gently pull out the bottle. 1 2 ZAET040E Fig. 5-6
CHAPTER 5 MAINTENANCE 5-5 ☛ ☛☛ ☛ 6.Move the new toner bottle back and forth about 5 – 6 times () and remove the black cap of the new toner bottle by turning it counterclockwise (). ZAET030E 1 2 Fig. 5-7 ✒ Note • Do not remove the inside cap. • After removing the black cap from the bottle, the toner can scatter easily. Do not shake or jar the bottle. ☛ ☛☛ ☛ 7.Push the Toner bottle into the toner holder () and push the top of the bottle downwards to lock it in place (). ZAET040E 1 2 Fig. 5-8
5-6 ☛ ☛☛ ☛ 8.Slide the toner holder into the printer until it clicks into place, and push down the green handle. ZAET022E Fig. 5-9 ☛ ☛☛ ☛ 9.Close the Front cover.
CHAPTER 5 MAINTENANCE 5-7 D D r r u u m m u u n n i i t t ! Replacing the Drum unit If the display shows the following message, the Drum should be changed. CHANGE DRUM SOON Warning • Do not incinerate the used drum unit. Toner dust might ignite when exposed to an open flame. • Disposal should take place at an authorized dealer or an appropriate collection site. • If you dispose of the used parts yourself, dispose of them according to local regulations. ☛ ☛☛ ☛ 1.Turn off the printer. ZAEH220E Fig. 5-10
5-8 ☛ ☛☛ ☛ 2.If the Duplex unit is installed, open the Duplex unit by lifting the catch. ZAEP330E Fig. 5-11 ☛ ☛☛ ☛ 3.Open the Right cover of the printer by lifting the catch. ZAEP271E Fig. 5-12 ☛ ☛☛ ☛ 4.Open the Front cover. ZAEM320E Fig. 5-13
CHAPTER 5 MAINTENANCE 5-9 ☛ ☛☛ ☛ 5.While pressing the green button, slide the Drum unit out until it stops. ZAEM330E Fig. 5-14 ☛ ☛☛ ☛ 6.Raise the green carrying handle and slide the Drum unit out. ZAEM340E Fig. 5-15 ✒ Note • Do not tilt or drop the removed Drum unit. Moving the unit abruptly can scatter toner. • While the Drum unit is removed, do not change the toner. ☛ ☛☛ ☛ 7.Take the new drum unit from the box and remove the plastic bag, holding the Drum unit by the carrying handle. ✒ Note • Do not drop or refit the removed Drum. • Do not touch the side of the Drum.
5-10 ☛ ☛☛ ☛ 8.Put the Drum unit removed in Step 6 into the plastic bag emptied in Step 7, keeping the unit at the same angle as when it was installed. Then, seal the plastic bag. ☛ ☛☛ ☛ 9.Remove the two red sheets from the Drum unit in the order shown in the illustration. ( ) ZAEM350E 1 2 Fig. 5-16 ✒ Note • Remove the drum unit keeping the unit parallel to the ground as shown in the illustration, otherwise the toner in the unit might scatter. • Do not touch the inside of the unit or the green parts after the black protection sheet is removed. ☛ ☛☛ ☛ 10.Align the new Drum unit onto the rail of the printer. Slide the unit all the way into the printer. ZAEM360E Fig. 5-17
CHAPTER 5 MAINTENANCE 5-11 ☛ ☛☛ ☛ 11.Push the Drum unit into the printer until it clicks into place. ZAEM370E Fig. 5-18 ☛ ☛☛ ☛ 12.Remove the red sheet from the Drum unit and remove the two pieces of tape. ZAEM410E Fig. 5-19 ☛ ☛☛ ☛ 13.Close the right side cover of the printer. ZAEM310E Fig. 5-20 ✒ Note If the Right side cover of the printer cannot be closed, it means that the Drum unit has not been properly installed. Slide the Drum unit out and push it into the printer again until it clicks into place.
5-12 ☛ ☛☛ ☛ 14.Close the Front cover. ZAEM380E Fig. 5-21 ☛ ☛☛ ☛ 15.If the Duplex unit is installed, close the Duplex unit cover. ZAEP270E Fig. 5-22 ☛ ☛☛ ☛ 16.Turn on the printer.