Brother Hl 3260n User Manual
Have a look at the manual Brother Hl 3260n User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4-38 ☛ ☛☛ ☛ 4.Push down the paper guide lever. ZAEY250E Fig. 4-62 ✒ ✒✒ ✒ Note If the paper guide lever is not pushed down, paper misfeeds may occur. ☛ ☛☛ ☛ 5.Turn on the printer. ☛ ☛☛ ☛ 6.Configure the paper feed unit direction and the paper size. ✒ ✒✒ ✒ Note The paper size specified with the printer driver overrides the one specified here.
CHAPTER 4 OPTIONS 4-39 M M a a i i l l b b o o x x u u n n i i t t ( ( M M X X - - 5 5 0 0 0 0 0 0 ) ) With this option, printed pages can be sent to four output trays. After installing the Interchange unit, install the Mailbox on the top of the Interchange unit. The Mailbox unit is an optional device that is installed onto the this laser printer that allows you to direct your printouts to any bin that you have specified. I I n n s s t t a a l l l l i i n n g g t t h h e e M M a a i i l l b b o o x x War ni ng When lifting the machine, use the hand holds on both sides of the printer. If dropped, the machine could be damaged or cause an injury ✒ Note • To install the mailbox, the Interchange unit must be installed first. • If you install the Mailbox and the Lower tray unit, it is recommended that the Lower tray unit is installed first. ☛ ☛☛ ☛ 1.Confirm that the box also contains the following items. 2 1 3 4 ZAEP383E Fig. 4-63 1. Mailbox output trays (4 pieces) 2. Screws (2 pieces) 3 Installation Guide 4 Output tray number seal
4-40 ☛ ☛☛ ☛ 2.Turn off the printer, and remove all cables and the power cord from the printer. ☛ ☛☛ ☛ 3.Remove the adhesive tape. ZAEP440E Fig. 4-64 ☛ ☛☛ ☛ 4.If you installed the Duplex unit, open the Duplex unit by lifting the catch. ZAEP330E Fig. 4-65 ☛ ☛☛ ☛ 5.Open the right cover by lifting the catch. ZAEP271E Fig. 4-66
CHAPTER 4 OPTIONS 4-41 ☛ ☛☛ ☛ 6.If the cover of the Interchange unit is attached, remove it by lifting the cover at the rear of the printer first as shown below. ZAEP710E 1 2 Fig. 4-67 ✒ Note • If the cover of the Interchange unit is already removed, go to Step 7. • The removed cover is no longer required. ☛ ☛☛ ☛ 7.Hold the Mailbox on both sides and fit it onto the top of the Interchange unit. ZAEP340E Fig. 4-68
4-42 ☛ ☛☛ ☛ 8.Fasten the two screws hand tight and secure the Mailbox to the printer. Use a coin to tighten the screws securely. ZAEP350E Fig. 4-69 ☛ ☛☛ ☛ 9.Close the Right cover by pushing the area as shown in the illustration. ZAEP690E Fig. 4-70 ☛ ☛☛ ☛ 10.If the Duplex unit is already attached, close the unit. ☛ ☛☛ ☛ 11.Slide the four mailbox output trays into the Mailbox unit starting from the bottom tray. ZAEP360E Fig. 4-71
CHAPTER 4 OPTIONS 4-43 ! #! $##%! #!#!& ( # ( )* # + ,& ♦ - ##! #% .# # .# !# # !. ! .# $., ♦ / ! .# %! # ! * # ! #. !# ! .# , 0# # !# ! # # # *!., ♦ 0# ! ! ! 1# % ! !# #. ! #$$, 0# ! ! # #$ ! !# 2 # !,
4-44 B B r r i i d d g g e e U U n n i i t t ( ( B B U U - - 5 5 0 0 0 0 0 0 ) ) With this option, printed pages are sent to the Finisher/Stapler. ✒ Note • If this Bridge unit is installed, the optional Finisher must be installed later. • If the mailbox is already installed, remove the four mailbox trays from the mailbox. I I n n s s t t a a l l l l i i n n g g t t h h e e B B r r i i d d g g e e U U n n i i t t ☛ ☛☛ ☛ 1.Confirm that the box also contains the following items. Fig. 4-72 1. Installation Guide 2. Bridge unit 3. Securing Plate 4. Knob Screw !Caution Unplug the printer power cord before starting the following procedure. 1 2 3 4
CHAPTER 4 OPTIONS 4-45 ☛ ☛☛ ☛ 2.Turn off the printer and remove all cables and cords from the printer. ☛ ☛☛ ☛ 3.Remove the adhesive tape. !Caution Do not remove the adhesive tape () holding the cable and the Bridge unit, until the Bridge unit is attached in step 14. 1 Fig. 4-73 ☛ ☛☛ ☛ 4.If you installed the Duplex unit, open the Duplex unit by lifting the catch. Fig. 4-74
4-46 ☛ ☛☛ ☛ 5.Open the Right cover of the printer by lifting the catch. Fig. 4-75 ☛ ☛☛ ☛ 6.Use a coin to remove the screw from the Front right cover and then remove the Front right cover. ✒ Note • The Front right cover has a clear film to prevent the removed screw falling in the printer. Do not remove the screw from the film. Fig. 4-76 • The removed screw and cover are required in step 11.
CHAPTER 4 OPTIONS 4-47 ☛ ☛☛ ☛ 7.Use a coin to remove the screw, and then remove the cover as shown in the illustration ✒ Note • The removed screw and cover are no longer required. Fig. 4-77 ☛ ☛☛ ☛ 8.Return the Paper sensor into the Output tray as shown in the illustration. Fig. 4-78 ☛ ☛☛ ☛ 9.Place the Bridge unit on the Output tray and slide the unit along the output part of the printer. Fig. 4-79