Brother Hl 3260n User Manual

							4-8
☛
☛☛ ☛ 6.Return the handles that were pulled out in step 4 to their original position.
☛
☛☛ ☛ 7.Slide Paper tray 2 out until it stops. Lift the front of the tray and then pull it
out completely.
ZAEP060E 
Fig. 4-9
☛
☛☛ ☛ 8.Use a coin to fasten the two screws that secure the paper feed unit and the
printer.
ZAEP070E 
Fig. 4-10
☛
☛☛ ☛ 9.Refit Paper tray 2.
 
						

							CHAPTER 4 OPTIONS
4-9
☛
☛☛ ☛ 10.Attach the two securing brackets on the back of the printer and the paper
feed unit, and fasten the screws using a coin.
ZAEP080E 
Fig. 4-11
☛
☛☛ ☛ 11.Remove the adhesive tape holding the cable and connect the harness to the
back of the printer.
ZAEP082E
Fig. 4-12
☛
☛☛ ☛ 12.Push the cable of the connected harness into the groove provided until it
stops.
ZAEP091E
Fig. 4-13
 
						

							4-10
☛
☛☛ ☛ 13.Attach cover 1 and secure it to the printer with the screws ➁.
1
2
ZAEP671E
Fig. 4-14
✒ Note
Insert the fastener into the hole after ensuring that the center push-in peg is
pulled out from the fastener as shown in the illustration.
☛
☛☛ ☛ 14.Attach cover 2 and secure cover 2 to the printer with the two screws.
ZAEP681E 
Fig. 4-15
☛
☛☛ ☛ 15.Turn the adjuster at the center bottom of the paper feed unit clockwise until it
touches the floor.
ZAEP100E 
Fig. 4-16
 
						

							CHAPTER 4 OPTIONS
4-11
☛
☛☛ ☛ 16.Fit the tray number seal directly below the paper size display on the front of
the paper feed tray.
Fig. 4-17
✒ Note
• Use the tray number seal included with the printer.
 
						

							4-12

 

 
 
 
 
 
 
 
	 	
 

 

 
 
 
 
 

 
 
 

 
 
 
 

 

 
 
 
 
 

 
 
 
 
 
 
 
 

 

	


	
		

		





				
	

	
	


 
		
	!	
	

	
	
 


 




	


 
#$
%&()#)

&*(
#

+ ,

-./!
0-1(2

	



 

#)	

 ,

-./!
0-1
2
✒
✒✒ ✒!

&	!3





	 

	4
✳5		

	
6	
	
,
0	!	
	!	

	6	
	,
7

6
$2
 
						

							CHAPTER 4 OPTIONS
4-13
With the lower tray unit installed, load paper into the lower paper tray in the
same way as you do the upper paper tray.
See “Loading paper in the standard paper tray” in Chapter 1.
S S
e e
t t
t t
i i
n n
g g
   
t t
h h
e e
   
M M
e e
d d
i i
a a
   
f f
r r
o o
m m
   
t t
h h
e e
   
P P
r r
i i
n n
t t
e e
r r
   
D D
r r
i i
v v
e e
r r
See “Setting the Media from the Printer Driver” in Chapter 1.
 
						

							4-14
I I
n n
t t
e e
r r
c c
h h
a a
n n
g g
e e
   
U U
n n
i i
t t
   
( (
S S
P P
- -
5 5
0 0
0 0
0 0
) )
With this option, printouts are sent to the Duplex unit or Mailbox.
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
t t
h h
e e
   
I I
n n
t t
e e
r r
c c
h h
a a
n n
g g
e e
   
u u
n n
i i
t t
☛
☛☛ ☛ 1.Confirm that the box also contains the following items.
•
•• • Installation Guide
☛
☛☛ ☛ 2.Turn off the printer, and remove all cables and power cords from the printer.
☛
☛☛ ☛ 3.Remove the adhesive tape and the packing materials.
Fig. 4-18
☛
☛☛ ☛ 4.Open the right cover of the printer by lifting the catch.
ZAEP140E 
Fig. 4-19
 
						

							CHAPTER 4 OPTIONS
4-15
☛
☛☛ ☛ 5.Open the upper right cover by lifting the handle.
ZAEP630E 
Fig. 4-20
☛
☛☛ ☛ 6.Press the upper right cover in the direction as shown in the illustration (),
and remove the upper right cover ().
✒ Note
The upper right cover is no longer required but should be kept safely if you
want to remove the Interchange unit in the future.
ZAEP150E 
Fig. 4-21
 
						

							4-16
☛
☛☛ ☛ 7.Use a coin to remove the screw from the upper cover of the printer.
✒ Note
The removed screw is no longer required but should be kept safely if you
want to remove the Interchange unit in the future.
ZAEP640E 
Fig. 4-22
☛
☛☛ ☛ 8.Put your fingers inside the upper cover of the printer and remove the cover
by pulling it upwards.
✒ Note
The upper cover of the printer is no longer required but should be kept
safely if you want to remove the Interchange unit in the future.
ZAEP650E 
Fig. 4-23
 
						

							CHAPTER 4 OPTIONS
4-17
☛
☛☛ ☛ 9.Remove the interchange unit cover from the interchange unit.
✒ Note
The removed cover is required in Step 15.
ZAEP500E
Fig. 4-24
☛
☛☛ ☛ 10.Position the cable towards the back of the printer. Place the interchange unit
onto the printer as shown in the illustration.
ZAEP700E
Fig. 4-25