Brother Hl 3260n User Manual
Have a look at the manual Brother Hl 3260n User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4-18 ☛ ☛☛ ☛ 11.Open the upper right cover () of the Interchange unit and slide the Interchange unit to the left while keeping the Upper cover right perpendicular to the printer (). Confirm that the projection ( ) locates in the hole as shown in the illustration. 13 1 2 Fig. 4-26 ☛ ☛☛ ☛ 12.Fasten the two screws finger tight and secure the Interchange unit to the printer. Use a coin to tighten the screws. ZAEP161E Fig. 4-27 ☛ ☛☛ ☛ 13.Close the Upper right cover of the Interchange unit. ZAEP162E Fig. 4-28
CHAPTER 4 OPTIONS 4-19 ☛ ☛☛ ☛ 14.Close the Right cover by pushing the area as shown in the illustration. ZAEP170E Fig. 4-29 ☛ ☛☛ ☛ 15.If a mailbox unit is not to be installed, attach the Interchange unit cover that was removed in step 9. Attach the side of the cover facing the front of the printer first () and then the other side of the cover (). ✒ Note To attach the mailbox, go to Installing the Mailbox, Step 6. ZAEP180E Fig. 4-30 ☛ ☛☛ ☛ 16.Attach the connector of the Interchange unit to the socket on the back of the printer as shown in the illustration. ZAEP190E Fig. 4-31
4-20 D D u u p p l l e e x x u u n n i i t t ( ( D D X X - - 5 5 0 0 0 0 0 0 ) ) After installing the Interchange unit, install the Duplex unit on the right hand side of the printer. The Duplex unit is an optional device that allows printing on both sides of pages. When it is installed, you can select either duplex printing or simplex printing from the Control panel or the printer driver. For more information about the control panel, see “Control Panel” in Chapter 3. If you want to duplex print, it is necessary to increase the installed RAM depending on the data you want to print. If the printer cannot manage all the data for duplex printing at 600 dpi resolution, it will automatically switch to simplex printing or decrease the resolution from 300 or 600 dpi to a lower resolution. I I n n s s t t a a l l l l i i n n g g t t h h e e D D u u p p l l e e x x U U n n i i t t The installation procedure for the Duplex unit when the Multi-purpose tray unit is not yet installed is described below. If the Multi-purpose tray unit is already installed, perform Steps 8 to 10 of “Installing the Multi-purpose tray” and skip Steps 5 to 8 below. ✒ Note To install the duplex unit, the interchange unit must be installed first.
CHAPTER 4 OPTIONS 4-21 ☛ ☛☛ ☛ 1.Confirm that the box also contains the following items. 1 2 3 4 5 6 7 ZAEP382E Fig. 4-32 1. Holder 2. Cover of the holder 3. Socket screws (3 pieces) 4. Allen Key 5. Hook 6. Hook holder 7. Installation Guide
4-22 ☛ ☛☛ ☛ 2.Turn off the printer, and remove all cables and the power cord from the printer. ☛ ☛☛ ☛ 3.Remove the adhesive tape and the packing materials. Fig. 4-33 ☛ ☛☛ ☛ 4.Remove the two small covers from the top right hand side of the Interchange unit. ✒ Note The removed small covers are no longer required. ZAEP200E Fig. 4-34
CHAPTER 4 OPTIONS 4-23 ☛ ☛☛ ☛ 5.Use a coin to remove the two screws on the right hand side of the printer. ✒ Note The removed screws are no longer required. ZAEP511E Fig. 4-35 ☛ ☛☛ ☛ 6.Use the Allen Key to remove the two screws from the cover on the right hand side of the printer and remove the cover. ✒ Note The removed screws and cover are no longer required. ZAEP510E Fig. 4-36 ☛ ☛☛ ☛ 7.Fit the brackets of the holder into the slots on the side of the printer and push downwards slightly. ZAEP210E Fig. 4-37
4-24 ☛ ☛☛ ☛ 8.Use the Allen Key to fasten the four socket screws in the order shown in the illustration (- ) to secure the holder to the printer. ✒ Note The order to fasten the screws is, top right, top left, bottom right and bottom left as viewed from the right hand side of the printer. If the screws are not fastened in that order, the duplex unit might not close completely or the Multi-purpose tray might not work correctly. ZAEP660E Fig. 4-38 ☛ ☛☛ ☛ 9.Remove the small cover on the right hand side of the printer. ✒ Note The removed small cover is no longer required. ZAEP230E Fig. 4-39
CHAPTER 4 OPTIONS 4-25 ☛ ☛☛ ☛ 10.Fit the brackets of the hook into the holes inside the cover that was removed in Step 9. Use the Allen Key to fasten the screw to secure the hook to the printer. ZAEP231E Fig. 4-40 ☛ ☛☛ ☛ 11.Lower the duplex unit so that the groove in each arm of the unit locates onto the pin inside the holder as shown in the illustration. ZAEP250E Fig. 4-41 ☛ ☛☛ ☛ 12.Locate the hole in the support bar of the duplex unit onto the pin on the hook that was attached in Step 10 (), and secure the bar by attaching the hook holder to the joint (). ZAEP260E 1 2 Fig. 4-42
4-26 ☛ ☛☛ ☛ 13.Close the duplex unit. ✒ Note If the duplex unit will not close completely, the holder was not installed correctly in Steps 7 and 8. Fasten the socket screws securely in the order described in Step 8. ZAEP270E Fig. 4-43 ☛ ☛☛ ☛ 14.Attach the connector of the duplex unit to the socket. ZAEP280E Fig. 4-44
CHAPTER 4 OPTIONS 4-27 ☛ ☛☛ ☛ 15.If the Multi-purpose tray is not attached, attach the cover of the holder. Use the Allen key to fasten the two screws in the order as shown in the illustration to secure the cover to the holder. ZAEP220E 1 2 Fig. 4-45 ✒ Note • When attaching the Multi-purpose tray, the cover of the holder is not required. • Keep the Allen Key in the housing inside the front cover. ZAEP540E Fig. 4-46