Xerox Phaser 8860MFP User Manual

Printing on Specialty Media
Phaser® 8560MFP/8860M FP Multifunction Printer
3-53
3.
Adjust the paper guides to fit  the glossy paper (if necessary).
■Length guide: Press the sides, and then slide  the guide until the arrow on the guide 
points to the appropriate paper size im printed on the bottom of the tray. When 
properly positioned, the  guide clicks into place.
■Width guides: Slide the width guides until the a rrows on the guides point to the 
appropriate paper size labeled on the bottom  of the...

Phaser® 8560MFP/8860MFP Multifunction Printer
3-54
4.
Insert the tray into the tray slot, and th en push it completely into the system.
Note: Do not load glossy pape r above the transparency fill line inside the tray. 
Overloading the tray may cause jams.
 5. On the control panel, press the  System button.
a. Select 
Paper Tray Setup, and then press the  OK button.
b. Select 
Tr a y  2  Pa p e r, Tr a y  3  P a p e r, or Tr a y  4  P a p e r, and then press the  OK button.
c. Select 
Use current setup...

Printing on Specialty Media
Phaser® 8560MFP/8860M FP Multifunction Printer
3-55
Printing Custom Size Paper
In addition to the wide variety of standard paper sizes that you can use for printing, you can 
also print on custom size paper  within the following dimensions.
 
Note: Print custom size paper from Tray 1 only.
See also: 
Paper Sizes and Weights for Tray 1  on page 3-7
Single-Sided Printing 2-Sided Printing
Short edge 76–216 mm (3.0–8.5 in.) 140–216 mm (5.5–8.5 in.)
Long edge 127–356 mm (5.0–14.0...

Printing on Specialty Media
Phaser® 8560MFP/8860M FP Multifunction Printer
3-56
Printing Custom Size Paper from Tray 1 
To print custom size paper:
1. Pull down and out on the handle to open Tray 1.
2. Open the tray extension.
8860mfp-011
8860mfp-012
Downloaded From ManualsPrinter.com Manuals 

Printing on Specialty Media
Phaser® 8560MFP/8860M FP Multifunction Printer
3-57
3.
Insert custom size paper into the tray.
■Single-sided printing : Insert the side to be printed  facedown with the top of the page 
entering the system first.
■2-sided printing : Insert side one faceup with the  bottom of the page entering the 
system first.
4. Adjust the paper guides to fit  the paper loaded in the tray.
8860mfp-109
8860mfp-110
Downloaded From ManualsPrinter.com Manuals 

Printing on Specialty Media
Phaser® 8560MFP/8860M FP Multifunction Printer
3-58
5.
Adjust the output tray for short or long media.
6. On the control panel, press the  OK button if the correct paper size and type are displayed 
as the current setup, or select th e appropriate paper size and type:
a. Select
 Change setup, and then press the  OK button. 
b. Select 
New Custom Size, and then press the  OK button.
c. Select one of the following options  for selecting the short edge size:
■If the size...

Creating Custom Paper Types
Phaser® 8560MFP/8860M FP Multifunction Printer
3-59
Creating Custom Paper Types
Using CentreWare IS, you can create your own cu stom paper type with specific settings that 
you can reuse for routine print jo bs, such as, monthly reports. Access these custom types in the 
printer driver, control panel, and CentreWare IS. 
Note: Creating custom paper types is not available on Phaser 8560MFP printers.
To create custom paper types:
1. Launch your web browser.
2. Enter the...

Phaser® 8560MFP/8860MFP Multifunction Printer
4-1
This chapter includes:
 ■Basic Copying 
on page 4-2
■Adjusting Copying Options  on page 4-3
■Managing Copy Functions on page 4-20
Note: Some of the features described in this chapter may not be available on your system 
configuration.
Copying
Downloaded From ManualsPrinter.com Manuals 

Basic Copying
Phaser® 8560MFP/8860M FP Multifunction Printer
4-2
Basic Copying
Use either the document glass or  the document feeder to make copies. Load the originals to be 
copied and follow the steps below to make copies . To clear the settings from the previous job, 
press the  Clear All  button once.
 
Note: For additional copying information, print th e Copying Guide. On the control panel, 
press the  Copy button, select 
Copying Guide, and then press the  OK button to print the guide.
 
1. On the...

Adjusting Copying Options
Phaser® 8560MFP/8860M FP Multifunction Printer
4-3
Adjusting Copying Options
This section includes:
 ■Basic Settings  on page 4-3
■Image Adjustments  on page 4-8
■Image Placement Adjustments  on page 4-13
■Output Adjustments on page 4-16
■Advanced Copying on page 4-18
Basic Settings
You can change the following basic settings:
■Selecting a Tray to Use for Copies  on page 4-3
■Setting the Copy Default Tray on page 4-4
■Selecting Color or Black and White Copies  on page 4-4...