Xerox 700 Digital Color Press User Manual

							
10-5
User Guide Addendum
Xerox 700 Digital Color Press
Fault code Possible cause Recommended solution
048 100
048 102
048 103
048 900
048 901
048 903 Paper jam
A jam occurred during feeding
•
A jam notification is displayed 
•
on the UI Open  the front door.
•
Carefully remove all sheets and paper scraps from 
•
jam clearance areas.
Close the front door. 
•
Verify the paper used is within the approved  paper 
•
specifications.
048 300 The front door is open. Close the front door.
048 310
048 311
048 312
048 313
048 314
048 315
048 316 Decurler sensor or belt problem
Power off, then power on
048 318
048 319 Cooling fan failure
  Power off, then power on
048 320
048 321
048 322 Communication failure or connection 
failure
Check the connection between Interface Module and 
•
the finishing device. 
Power off, then power on.
•
048 323 Interface Module failure Power off, then power on
Fault codes
Downloaded From ManualsPrinter.com Manuals 
						

							
10-6User Guide
Xerox 700 Digital Color Press
Addendum
100V to 240V
Frequency: 50/60 Hz
10 to 32°C, 15 to 85RH
50 to 90°F, 15 to 85RH
Above 82°F (28°C), reduced humidity is required to maintain the \
specified performance.
Specifications
Electrical
Temperature and humidity
Downloaded From ManualsPrinter.com Manuals 
						

							
10-7
User Guide Addendum
Xerox 700 Digital Color Press
The High Capacity Stacker (HCS) is an optional finishing device 
that provides stacking and offsetting capabilities for output to 
a Stacker Tray. The HCS connects to the right side of the digital 
press by way of the Interface Module.  The HCS replaces the 
Offset Catch Tray (OCT). Interface Module
High Capacity Stacker (HCS)
The major components of the HCS are as follows:
High Capacity Stacker (HCS)
Overview
Identifying the components
Control Panel - Provides manual control of the various functions 
of the HCS.
Top Tray - Up to 500 sheets are transported to the Top Tray:
When sheets are purged after a paper jam.
•
When the Sample Set button is selected.
•
When selected as an Output Location.
•
Labels must be sent to the Top Tray.
•
Bypass - Only used when a second stacking/finishing device is 
installed. This path transports collated sets through the HCS to a 
connected finishing device or to another HCS.
Stacker Tray/Cart - Collated sets (up to a total of 5000 sheets) are 
transported to the Stacker Tray located on a moveable Stacker 
Cart.
If your system configuration has two stackers, the bypass on the 
second stacker is not used.
12
3
Downloaded From ManualsPrinter.com Manuals 
						

							
10-8User Guide
Xerox 700 Digital Color Press
Addendum
Control Panel
The HCS Control Panel consists of:
Sample indicator:
This indicator blinks until a proof set is delivered to the 
Top Tray.
Sample button:
Press this button to have the HCS deliver the next 
collated set to the top tray.
Unload button:
Press once to lower the Stacker Tray and unlock the front 
door.
Unload indicator:
This indicator lights when the Stacker Tray has reached 
the down position and the front door can be opened.
Top Tray jam area:
Blinks when there is a jam in the top tray area (E7).
Exit jam area:
Blinks where there is a jam in  the exit area (E8).
Stacker Entrance jam area:
Blinks when there is a jam in the Stacker Entrance area 
(E1, E2, or E3).
Stacker Transport jam area:
Blinks when there is a jam in the Stacker Transport area 
(E4, E5, or E6).
1
2
3
5
48
7
6
Downloaded From ManualsPrinter.com Manuals 
						

							
10-9
User Guide Addendum
Xerox 700 Digital Color Press
The Top Tray offers the following:
Copies/prints are aligned easily without folds or winkles in the output.\
•
To enable easier pick-up of the ouput copies/prints, the HCS can be stop\
ped by selecting the Stop button on 
•
the machine's UI.
HCS Trays
Top Tray
Sample Print feature
Sample prints can be printed by performing the following steps:
1.From the [Copy Output] feature, select: Collated or Uncollated
•
Output Destination/Offset Stacker
•
2.Select [Stacker - Stacker Cart] then [Real Time Sample Job].
3.Select [Sample Job On].The [Sample Job On] feature delivers specific p\
ages or sets of an output job to the High 
Capacity Stacker’s Top Tray.The Sample Job allows the user to check t\
he output while continuing to deliver the major 
portion of the job to the Stacker Cart. For Collated output, for example, if the output is 100 sets of a 50-page\
 original document, the user can choose 
•
1-3 output sample sets.
For Uncollated output, for example, if the output is 100 copies of each \
page of a 50-page original document, 
•
the user can choose 1-3 sample pages4.Enter the desired Sample pages/set\
s to print for the [First Sample] and 
then for the [Second Sample] and [ThirdSample] (if applicable).5.Selec\
t [Save].
Downloaded From ManualsPrinter.com Manuals 
						

							
10-10User Guide
Xerox 700 Digital Color Press
Addendum
Unloading the Stacker Tray
Use the following procedure to unload the Stacker Tray when it is full, \
or to retrieve a completed job.
Press the Unload button on the HCS Control Panel. The 
Wait light blinks until the Stacker Tray has reached the 
down position.
Open the front door when the Unload Light illuminates.
Position the securing bar on top of the stacked paper.
Pull the Stacker Cart straight out. Remove the securing 
bar.
Remove the paper from the Stacker Tray.
Push the empty Stacker Cart straight into the HCS.
Position the securing bar on the fixed area inside the 
HCS.
Close the door. The tray will rise to the operate position.
Downloaded From ManualsPrinter.com Manuals 
						

							
10-11
User Guide Addendum
Xerox 700 Digital Color Press
If a jam occurs, the machine stops printing and a message is displayed o\
n the User Interface (UI). Follow all 
instructions displayed completely and in the sequence shown.
Jam clearance
HCS Entrance Jams (E1, E2, and E3)
Perform the following steps to clear the HCS Entrance jam and resume pri\
nting.
HCS Transport Jams (E4, E5, and E6)
Perform the following steps to clear the HCS Transport jam and resume pr\
inting.
Open the HCS Front Cover.
Follow the instructions located inside the Front Cover to 
clear the E1, E2, or E3 jam.
Lift the green handle and/or rotate the green knob and 
remove all paper in the entrance area.
Close the green handle.
Close the HCS Front Cover.
If the UI indicates there is a jam in the digital press, 
follow the instructions on the screen to remove any paper 
in the area indicates. Refer to the Jam Clearance section 
in the Problem Solving chapter in this manual.
Follow the instructions displayed on the digital press UI 
to resume printing.
Open the HCS Front Cover.
Follow the instructions located inside the Front Cover to 
clear the E4, E5, or E6 jam.
Lift the green handle and/or rotate the green knob and 
remove all paper in the transport area.
Close the green handle.
Close the HCS Front Cover.
If the UI indicates there is a jam in the digital press, 
follow the instructions on the screen to remove any paper 
in the area indicates. Refer to the Jam Clearance section 
in the Problem Solving chapter in this manual.
Follow the instructions displayed on the digital press UI 
to resume printing.
Downloaded From ManualsPrinter.com Manuals 
						

							
10-12User Guide
Xerox 700 Digital Color Press
Addendum
HCS Top Tray Jam (E7)
Perform the following steps to clear the HCS Top Tray jam and resume pri\
nting.
Open the HCS Front Cover.
Follow the instructions located inside the Front Cover to 
clear the E1, E2, or E3 jam.
Remove the jammed paper from the Top Tray.
Close the HCS Front Cover.
If the UI indicates there is a jam in the digital press, 
follow the instructions on the screen to remove any 
paper in the area indicates. Refer to the Jam Clearance 
section in the Problem Solving chapter in this manual.
Follow the instructions displayed on the digital press UI 
to resume printing.
HCS Exit Jam (E8)
Perform the following steps to clear the HCS Exit jam and resume printin\
g.
Open the HCS Front Cover.
Follow the instructions located inside the Front Cover to 
clear the E8 jam.
Lift the green handle and/or rotate the green knob and 
remove all paper in the exit area.
Close the HCS Front Cover.
If the UI indicates there is a jam in the digital press, 
follow the instructions on the screen to remove any 
paper in the area indicates. Refer to the Jam Clearance 
section in the Problem Solving chapter in this manual.
Follow the instructions displayed on the digital press UI 
to resume printing.
Downloaded From ManualsPrinter.com Manuals 
						

							
10-13
User Guide Addendum
Xerox 700 Digital Color Press
Fault code Possible cause Recommended solution
049 100
049 101
049 102
049 104
049 106
049 108
049 113
049 114
049 115
049 116
049 117
049 119
049 121
049 900
049 901
049 902
049 903
049 905
049 907
049 908 Paper jam
A jam occurred during feeding
•
A jam notification is displayed 
•
on the UI Open  the front door.
•
Carefully remove all sheets and paper scraps from 
•
jam clearance areas.
Close the front door. 
•
Verify the paper used is within the approved  paper 
•
specifications.
049 210
049 211 Front door sensor problem Power off, then power on
049 212
049 213 Stacker problem
Power off, then power on
Fault codes
Downloaded From ManualsPrinter.com Manuals 
						

							
10-14User Guide
Xerox 700 Digital Color Press
Addendum
Fault code Possible cause Recommended solution
049 214
049 215
049 216
049 217
049 218 Senor problem/failure Power off, then power on
049 219 Front door software failure The front door switch is detected as "open," but the front door  is actually closed (locked).  Power off, then power on.
049 220
049 221 Stacker upper limit failure
•
Stacker lower limit failure
• Power off, then power on
049 222
049 223
049 224
049 225
049 228
049 229
049 232
049 233
049 234
049 235
049 236
049 237
049 238
049 239
049 240
049 241
049 242
049 243
049 244
049 245
049 246
049 247
049 248
049 249
049 250
049 251
049 252
049 253 Senor problem/failure Power off, then power on
Downloaded From ManualsPrinter.com Manuals