Vodavi Starplus Triad S Installation Programming Manual

Distinctive Ringing2-115
Chapter 2 - Features and Operation
4. Press the Page B flexible button (Button #20). The following message displays:
XXX-XXX = CO Line Range
5. Press the RING TONE flexible button (FLASH 40, Page B, Button #6). The following 
message displays:
6. Enter a valid number on the dial pad to change this feature.
7. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … Ring Tone is set for 00 (697/770).
XXX - XXX  PAGE  B
ENTER  BUTTON  NUMBER
RING...

2-116Distinctive Ringing
Chapter 2 - Features and Operation
Enabling/Disabling Distinctive Ring Tone
Description
The distinctive ring tone feature must be enabled and disabled in admin programming.
Programming Steps
1. Press the CO RING TONE flexible button (FLASH 06, Button #2). The following message 
displays:
2. Enter a 0 or 1 on the dial pad to enable/disable the tone ring signal.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … CO Ring Tones is...

Distinctive Ringing2-117
Chapter 2 - Features and Operation
The ringing choices are as follows:
Conditions
» Station users may listen to all tones by dialing the 2-digit codes one after another. The 
tone that is sounding when the SPEED button is pressed is saved as that station’s tone 
ringing selection.
» A station’s tone ringing selection is maintained in a battery protected area of memory. 
Therefore, if a system experiences a power failure or a soft or hard restart, the tone 
ringing selection is...

2-118Do Not Disturb
Chapter 2 - Features and Operation
Do Not Disturb
Description
Placing a keyset in Do Not Disturb (DND) eliminates incoming outside line ringing, intercom 
calls, transfers and paging announcements. A ringing station may go into DND to silence 
ringing. The Attendant can override a station in DND. Stations in DND can continue to make 
normal outgoing calls.
Stations can be individually allowed or denied the ability to place their telephone in Do Not 
Disturb. By default, Do Not Disturb...

Do Not Disturb2-119
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the DO NOT DISTURB flexible button (Button #2). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Do Not Disturb is...

2-120Do Not Disturb
Chapter 2 - Features and Operation
» DND capability is programmable on a per-station basis.
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
One-Time Do Not Disturb
Description
Prevents calls from ringing at your station while you are on a call. The One-Time DND 
condition automatically...

Executive Override2-121
Chapter 2 - Features and Operation
Do Not Disturb - DSS / BLF Flash Rate
Description
The Do Not Disturb DSS/BLF flash rate is the rate at which a DSS button of a station flashes 
when you are in a Do Not Disturb mode. This flash rate can be programmed to 29 different 
options identified in the flash rate table. This enables the programmer to customize the key 
system configuration to desired flash rates.
Programming Steps
1. Press the DND – DSS/BLF flexible button (FLASH 07,...

2-122Executive Override
Chapter 2 - Features and Operation
A separate condition has been added to this feature which allows or disallows an Executive to 
override an extension. This prevents an extension with override capability from overriding an 
Executive’s station.
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press...

Executive Override2-123
Chapter 2 - Features and Operation
4. Press the EXECUTIVE OVERRIDE flexible button (Button #4). The following message 
displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Executive Override is disabled for all stations.
Operation
To use Executive Override, when calling a busy station:
1. Press the preprogrammed EXECUTIVE OVERRIDE button (The programming code...

2-124Executive Override
Chapter 2 - Features and Operation
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Executive Override Blocking
Description
The Executive Override Blocking feature allows or disallows override of an extension. This 
prevents a user with override capability from overriding a station.
Use...