Vodavi Starplus Triad S Installation Programming Manual

CO Line - Ringing Options2-85
Chapter 2 - Features and Operation
CO Direction
Description
CO Lines can be programmed on a per CO Line basis for the type of CO Line desired:
Incoming

Incoming restricts the CO Line for incoming calls only.

Users can place call on hold, park the call, and other stations can pick up the call.
Outgoing

Outgoing restricts the CO Line to outgoing calls only.

Users can place call on hold, park the call, and other stations can pick up the call.
Incoming and Outgoing

Incoming...

2-86CO Port Parameters
Chapter 2 - Features and Operation
5. Enter a valid number (0-3) on the dial pad which corresponds to the desired CO type:
[0] = Out-of-Service (OOS)
[1] = Incoming Only
[2] = Outgoing Only
[3] = Both Incoming and Outgoing
6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … All CO Lines default to both incoming and outgoing type.
Conditions
» For PRI cards, the 24th channel must be marked as Out-of-Service (OOS). This is true on all 
PRI...

CO Port Parameters2-87
Chapter 2 - Features and Operation
Print CO Port Parameters and Feature Codes
Description
The Print CO Port Parameters and Feature Codes command dumps the entire database as a 
permanent record which can serve as a hardcopy of the database. The system baud rate must 
match that of the printer or receiving device.
Figure 2-5: CO Port Attributes and Feature Codes Printout
Programming Steps
1. Press the CO PORTS/CODES flexible button (FLASH 85, Button #4). The following 
message...

2-88CO Ring Detect Timer
Chapter 2 - Features and Operation
CO Ring Detect Timer
Description
The CO Ring Detect Timer controls the time necessary to detect an outside line ringing into 
the system. The duration of the ringing signal from the CO or the PBX is matched with ringing 
detection circuitry in the Triad-S. The ring detect can range from 200 ms to 900 ms 
programmed in 100 ms increments. This timer helps prevent false ringing.
Programming Steps
1. Press the CO RING DETECT TIMER flexible button...

Conference2-89
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible...

2-90Conference
Chapter 2 - Features and Operation
Conference / DISA Timer
Description
The Conference/DISA Timer determines the time an unsupervised conference can continue 
after the initiator of the conference has exited.
The Conference/DISA Timer setting is variable from 01-99 minutes. A 00 entry disables the 
timer and no automatic disconnect occurs.
Programming Steps
1. Press the CONFERENCE/DISA TIMER flexible button (FLASH 01, Button #9). The following 
message displays:
2. Enter a valid number on...

Conference2-91
Chapter 2 - Features and Operation
Operation
To establish a Conference:
1. Lift handset.
2. Select intercom station or dial desired outside party.
3. When called party answers, press the CONF button.
4. Add next conference party by selecting another outside line or intercom station.
5. If the next conference party is an outside line and a busy or wrong number is 
encountered, press one of the conference parties on hold. This drops the busy or wrong 
number party. Press the conference...

2-92 Co rd l e ss Key Te le ph o ne  Un it  Fea tu re  But to n
Chapter 2 - Features and Operation

SINGLE LINE TELEPHONE
To set up a Conference with one external and one other internal station:
1. Make outside call.
2. Briefly depress and release the hookswitch to put the call on hold.
3. Dial number of internal station you wish to add.
4. When that station answers, briefly depress and release hookswitch again. All three parties 
will be connected.
To set up a Conference with Personal Park:
1. While...

Cordless Key Telephone Unit Feature Button 2-93
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The...

2-94Database Administration
Chapter 2 - Features and Operation
Database Administration
Administration Access
Description
The Administration Access feature allows a station to access Database Administration. Each 
station can be enabled/disabled for system programming.
Related Information
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number....