Vodavi Starplus Triad S Installation Programming Manual

Call Forward - Preset2-35
Chapter 2 - Features and Operation
External Busy Destination
1. Press Button #4. The following message displays:
2. Enter a valid flexible number and press HOLD.
3. To delete the entry, press the [#] key and then press HOLD.
No Answer Timer
1. Press Button #5. The following message displays:
2. Enter a valid number (00-99) and press HOLD (00=disable).
DEFAULT … No Answer Timer is set at 10 seconds.
Conditions
» Station Forwarding overrides the Preset Forward settings.
» Only one...

2-36Call Forward - Preset
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible Button #19 (Page A) is lit.
4. Press the Page B flexible button (Button #20). The following message displays:
XXX-XXX = CO Line Range
5. Press the PRESET FWD DESTINATION flexible button (Button #2). The following message 
displays:
6. Enter a valid forward destination on the dial pad.
[9020-9999] = System Speed Bins
[100-131] = Station Extensions...

Call Forward - Preset2-37
Chapter 2 - Features and Operation
Preset Forward Timer (Incoming Call to a Destination)
Description
The Preset Forward Timer determines the time an outside line rings before being forwarded 
to a predetermined destination as programmed in FLASH 50, Page C, Buttons 1-4. If a forward 
destination is programmed in the CO line field, the CO calls forward to that destination after 
the CO preset forward timer expires. This forward occurs regardless of how many stations the 
line is...

2-38Calling Forward Override
Chapter 2 - Features and Operation
Calling Forward Override
Description
The Call Forward Override feature allows a user to reach a station that is call forwarded. This 
allows the calling station to override the forwarding which allows the user to use Off Hook 
Voice Over (OHVO), Executive Override, Monitor, Message Wait Indication, Camp On, or Call 
Back Request at that station rather than forwarding to another destination.
Operation
1. Dial [5#] followed by the desired...

Call Park2-39
Chapter 2 - Features and Operation
Call Park
Call Park - System
Description
An outside line can be placed into one of eight system park locations and can be retrieved by 
any station that has a direct line appearance or an available Loop button. Parked calls have 
their own recall timer that recalls the originating station, and if still unanswered, the 
Attendant(s). An outside line may also be placed into a station park location. The station user 
then dials a code followed by their...

2-40Call Park
Chapter 2 - Features and Operation
» A CO call parked in a system call park location recalls to the station that parked the call, 
when the call park recall timer expires. The CO call rings to this station until the system 
hold timer expires. The CO call then recalls the Attendant (both the Attendant and 
initiating stations are ringing), and the Attendant recall timer is initiated. When the 
Attendant recall timer expires, the CO call is disconnected.
Call Park Recall Timer
Description...

Call Park2-41
Chapter 2 - Features and Operation
Operation
To park a call, while connected to an outside line:
1. Press the TRANS button. The caller is put on Exclusive Hold.
2. Dial the Personal Park location [438] on the dial pad,
-or-
Press the preprogrammed PERSONAL PARK button.
Dial tone sounds.
To retrieve a parked call:
Dial the Personal Call Park location code [438] on the dial pad,
-or-
Press the preprogrammed PERSONAL PARK button.
A talk path is established between the two parties.

SINGLE...

2-42Call Pickup
Chapter 2 - Features and Operation
Call Park - Station
Description
Call park (by station number) allows calls to be parked at stations, thus allowing for expanded 
park locations.
Operation
While connected to an outside line:
1. Press TRANS button.
2. Dial [439] + [XXX] (XXX=station number). A confirmation tone sounds.
Call Park Pickup - Station
To retrieve a Station Park Call:
Dial [# 6] + user’s station number, while at the user’s telephone or from any telephone in the 
system.
-or-...

Call Pickup2-43
Chapter 2 - Features and Operation
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being...

2-44Call Pickup
Chapter 2 - Features and Operation
6. Enter a valid number (1-8) to program Pickup Groups.
7. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … All stations are in Group 1.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Directed Call Pickup...