Vodavi Starplus Triad S Installation Programming Manual

CO Line Group2-65
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect current...

2-66CO Line Group
Chapter 2 - Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
CO Line Group Programming
Description
Twenty four line groups are available for CO line assignment. Groups should be assigned 
according to type (local, FX, WATS, etc.). All unassigned CO lines should...

CO Line - Identification2-67
Chapter 2 - Features and Operation
5. Enter a valid number on the dial pad (0-23) which corresponds to Groups 0-23.
6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … All lines are placed in Line Group 1.
CO Line - Identification
Description
The CO Line Identification feature allows entering a name into the database for each 
individual line (trunk) connected to the system. The name may be entered in any 
combination up to...

2-68CO Line - Identification
Chapter 2 - Features and Operation
Programming Steps
Each CO line can be programmed to have a name associated to it in database programming.
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following...

CO Line - Incoming Ringing Assignment 2-69
Chapter 2 - Features and Operation
6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
CO Line - Incoming Ringing Assignment
Description
Each CO line may be programmed (in database admin) so that incoming ringing on the 
specified CO line(s) may be assigned initial ringing to one of the following destinations:

One or more stations (Keyset or SLT )

An ACD, UCD, Voice Mail or Hunt Group

Off-Net (via Speed Dial)
The ring-in...

2-70 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of...

CO Line - Incoming Ringing Assignment 2-71
Chapter 2 - Features and Operation
* Internal flexible numbers range = 100-8999
To add multiple stations:
Enter: DDDDR HOLD DDDDR HOLD DDDDR HOLD...etc.
(Example: 10073 HOLD, 10083 HOLD, 10093 HOLD)
To delete a single station:
Enter: DDDD0 HOLD
(Example: 10080 HOLD)
To delete multiple stations:
Enter: DDDD0 HOLD DDDD0 HOLD...etc.
(Example: 10080 HOLD, 10090 HOLD)
DEFAULT … All CO lines ring at the Attendant, Station 100 during Day and Night Modes.
Table 2-4: CO...

2-72 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
Incoming CO Line Ringing - Setting Flash Rate
Description
The Incoming CO Line Ringing flash rate is the rate at which an Incoming CO line or Loop 
Button flashes. This flash rate can be programmed to 29 different options identified in the 
flash rate table, which enables the programmer to customize the key system configuration to 
desired flash rates.
Programming Steps
1. Press the INC CO RING flexible button (FLASH 07, Button...

CO Line - Incoming Ringing Assignment 2-73
Chapter 2 - Features and Operation
4. Press FLASH 40, Page A, Button #13 to display ring assignments. Assignments are 
displayed in sets of six, up to the number programmed. The following format displays the 
assignments.
XDDDD = Destination type ID letter fllowed by number to be dialed:
     [F]] plus Fixed Number, e.g., F102
     [H] plus Hunt Group Number, e.g., H6700
     [M] plus Modem Extension Number, e.g., M6099 (default = M499N)
     [R] plus Recorded...

2-74 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
Guard Timer
Description
The outgoing Guard Timer is used to set the length of time a CO is held busy to outgoing 
seizure after a valid release is detected. If a user attempts to access a CO line before the Guard 
Timer expires, their LED illuminates to indicate that the line is seized, however the CO line is 
not actually seized until the timer expires. The user gets a busy tone, and may receive a 
delayed CO dial tone if the...