Vodavi Starplus Triad S Installation Programming Manual

Database Administration2-95
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the ADMIN ACCESS flexible button (Button #18). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disable
[1] = Enable
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … This feature is...

2-96Database Administration
Chapter 2 - Features and Operation
Administration Password
Description
The password used to enter customer database programming can be customized by the 
programmer. This lets the system administrator block unauthorized personnel from entering 
database admin.
Programming Steps
1. Press the ADMIN PASSWORD flexible button (FLASH 20, Button #2). The following 
message displays:
2. Enter a valid number on the dial pad that corresponds with 0000-9999.
3. Press HOLD to save the...

Database Printout (Dump)2-97
Chapter 2 - Features and Operation
Database Printout (Dump)
Description
Through a system programming command, either portions of or a complete database dump 
can be printed using an RS-232C connector located on the optional MISB.
The Print System Database command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
Printing the entire database takes a while to...

2-98Dial Pulse Sending
Chapter 2 - Features and Operation
Dial Pulse Sending
Description
Each CO interface circuit for outside lines can be programmed to send dial pulse or DTMF 
signals. Dialing speed and break/make ratios are programmable.
Dial Pulse Parameters
Description
The Dial Pulse option lets the installer adjust the dial pulse ratio and speed when using dial 
pulse (rotary) type signaling. By default, all lines are DTMF (tone) signaling. If pulse dialing is 
required, the individual outside...

Dial Pulse Sending2-99
Chapter 2 - Features and Operation
Programming Steps
1. Press the PULSE DIAL I/D TIMER flexible button (FLASH 02, Button #5). The following 
message displays:
2. Enter a valid number on the dial pad that corresponds to 300-600 ms.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … Pulse Dial Ring Timer is set for 300 ms.
Pulse-to-Tone Switchover
Description
When commanded, the system changes the signaling on an outside line from dial...

2-100Dial Pulse Sending
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [43]. The following message displays:
000 = Route Number (000–251)
DDDD = 3- or 4-Digit Ringing Destination Number
R = Ringing Type
2. Press the RING ASSIGNMENT flexible button (FLASH 43, Button #1). LED #1 is lit 
indicating Route 000 is ready for programming.
3. Enter a valid Destination (DDD) or (DDDD) and Ring type (R) followed by HOLD. A 
confirmation tone sounds and the display updates.
* Internal...

Dial Pulse Sending2-101
Chapter 2 - Features and Operation
XDDDD = Destination type ID letter fllowed by number to be dialed:
     [F]] plus Fixed Number, e.g., F102
     [H] plus Hunt Group Number, e.g., H6700
     [M] plus Modem Extension Number, e.g., M6099 (default = M499N)
     [R] plus Recorded Announcement Extension Number, e.g., R6020
     [S] plus Station Number, e.g., S6002
     [U] plus UCD/ACD Group/Agent Number, e.g., U6034
     [V] plus Voice Mail Group Number, e.g., V6899
     [B] plus...

2-102 D ire c t In w a rd  Syste m Ac c ess  (D IS A )
Chapter 2 - Features and Operation
Direct Inward System Access (DISA)
The Triad-S allows programming of an unlimited number of outside line calls to provide 
direct access to the system. DISA callers may access LCR, All Internal/External Paging, All Call 
Paging, Call Park Pick-Up, and Meet-Me Paging. A DTMF receiver must be available for DISA 
operation. The duration of a trunk-to-trunk DISA call can be set by system administrator.
Incoming DISA...

Direct Inward System Access (DISA) 2-103
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of...

2-104 D ire c t In w a rd  Syste m Ac c ess  (D IS A )
Chapter 2 - Features and Operation
DISA CO-to-CO
Description
The DISA CO-to-CO (or Conference) option on the CO line governs a DISA caller’s ability to 
access other outside lines. CO lines must have DISA CO-to-CO enabled to allow a DISA caller 
to establish an outgoing CO-to-CO connection. This allows for specific CO line access 
restriction on DISA calls. A station with Conference enabled can initiate a conference on CO 
lines regardless of the CO...