Vodavi Starplus Triad S Installation Programming Manual

C O L in e Loo p a n d  Po ol Bu tto ns 2-75
Chapter 2 - Features and Operation
4. Press the Page B flexible button (Button #20). The following message displays:
XXX-XXX = CO Line Range
5. Press the TRANSMIT VOLUME flexible button (FLASH 40, Page B, Button #1). The 
following message displays:
6. Enter a valid number (0-9) for the desired volume level.
7. When the desired level is selected, press HOLD to complete the entry. A confirmation 
tone sounds and the display updates.
DEFAULT … All CO lines are...

2-76 CO  L in e L oop  a n d  Po ol B ut ton s
Chapter 2 - Features and Operation
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-131) to be programmed....

C O L in e Loo p a n d  Po ol Bu tto ns 2-77
Chapter 2 - Features and Operation
Operation
To make a Loop button:
1. Press the SPEED button twice.
2. Press the desired flexible button.
3. Dial [89].
4. Press HOLD.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
In-Use Hold (I-Hold) Flash Rate...

2-78CO Line - Loop Supervision
Chapter 2 - Features and Operation
CO Line - Loop Supervision
Description
The Triad-S can be programmed to monitor CO lines while on-hold or connected to RAN 
devices or Voice Mail systems, or in Trunk-to-Trunk connections for disconnect signal 
provided by the Telco. After a disconnect signal is detected, the Triad-S releases the CO lines 
and automatically place them back in service.
Loop Supervision Programming
Description
Loop Supervision is used primarily with DISA,...

CO Line - Queue2-79
Chapter 2 - Features and Operation
CO Line - Queue
Description
When all outside lines in a group are busy, stations can be placed in queue awaiting a line in 
the same group to become available. If a station doesn’t answer the queue signal within 
15 seconds, that station is dropped from the queue. A station can queue only one line at a 
time.
Line Queuing
Description
Stations can be allowed or denied the ability to manually queue for a busy group of CO lines. 
Even when disabled,...

2-80CO Line - Queue
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the QUEUING flexible button (Button #7). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … CO Line Queuing is enabled at...

CO Line - Ringing Options2-81
Chapter 2 - Features and Operation
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
CO Line Queue Button Flash Rate
Description
The Line Queue Button flash rate is the rate at which the Line Queue button flashes after 
queueing onto a busy line. This button flashes when the busy line becomes available. This 
flash rate can be programmed to 29 different options...

2-82CO Line - Ringing Options
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the RINGING OPTIONS flexible button...

CO Line - Ringing Options2-83
Chapter 2 - Features and Operation
Programming Steps
1. Press the TRANSFER CO RING flexible button (FLASH 07, Button #9). The following 
message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of the 29 available 
options. (Refer to Table 2-11 on page 2-130.)
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … Transfer CO Ringing flash rate is set for a Red 120 ipm Flash (10).
Recall CO Ringing...

2-84CO Line - Ringing Options
Chapter 2 - Features and Operation
Queued CO Ringing Flash Rate
Description
The Queued CO Ringing flash rate is the rate at which a CO Line button or Loop button 
flashes when a queued line becomes available. This flash rate can be programmed to 
29 different options identified in the flash rate table. This enables the programmer to 
customize the key system configuration to desired flash rates.
Programming Steps
1. Press the QUEUED CO RING flexible button (FLASH 07, Button...