Vodavi Starplus Triad S Installation Programming Manual

Class Of Service2-55
Chapter 2 - Features and Operation
Class of Service - CO Line
Description
Through assignments of a CO Line Class of Service, the assigned CO line interacts with a 
station Class of Service.
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display...

2-56Class Of Service
Chapter 2 - Features and Operation
Station Day Class of Service
Description
Each station must be assigned a certain COS for Day Mode operation and for Night Mode 
operation. Class of Service (COS) determines the station’s dialing privileges.
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and...

Class Of Service2-57
Chapter 2 - Features and Operation
5. Press the DAY COS flexible button (Button #2).
6. Enter a valid number on the dial pad (1-7) corresponding to one of seven possible Classes 
of Service to which a station may be assigned.
The seven classes of service are:
[1] = COS 1; No restrictions
[2] = COS 2; Table A governs
[3] = COS 3; Table B governs
[4] = COS 4; Table A and B govern
[5] = COS 5; Restricts [0], [1], [

], [#] dialed as first-digit with a 7-digit maximum
[6] = COS 6;...

2-58Class Of Service
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates....

CO Line - Access2-59
Chapter 2 - Features and Operation
6. Enter a valid number on the dial pad (1-7) corresponding to one of seven possible Classes 
of Service to which a station may be assigned.
The seven Classes of Service are:
[1] = COS 1; No restrictions.
[2] = COS 2; Table A governs
[3] = COS 3; Table B governs
[4] = COS 4; Table A and B govern
[5] = COS 5; Restricts [0], [1], [

], [#] dialed as first-digit and places a 7-digit maximum.
[6] = COS 6; Intercom Only (no CO line access - results in a...

2-60CO Line Attributes
Chapter 2 - Features and Operation
Conditions
» Access to trunk group must be programmed by installer/administrator.
» The CO line must be idle.
CO Line Attributes
Initialize CO Line Attributes
Description
CO Line parameters may be initialized to set all data fields to their original, default values. The 
following data fields are returned to their default value upon initializing the CO Line 
Attributes.
Table 2-3: CO Line Attribute Defaults
Program 
CodeFlexible...

CO Line Attributes2-61
Chapter 2 - Features and Operation
Programming Steps
1. Press the CO LINE ATTRIBUTES flexible button (FLASH 80, Button #2). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
Print CO Line Attributes
Description
The Print CO Line Attributes command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database The system baud rate must match that of the 
printer or receiving device.
When printing the CO Line...

2-62CO Line Attributes
Chapter 2 - Features and Operation
Figure 2-3: CO Line Attributes Printout
Programming Steps
1. Press the CO LINE ATTRIBUTES flexible button (FLASH 85, Button #2).
2. To print data for:

ALL CO Lines, press the HOLD button.

A specified CO Line Range, enter 6 digits ( 3 digits for the first line and 3 digits for the 
last line in the range):

One CO Line, enter that line twice: [001001]
3. Then press the HOLD button. The following message displays and the CO Line data prints:
When...

CO Line DTMF Sending2-63
Chapter 2 - Features and Operation
CO Line DTMF Sending
Each CO interface circuit for outside lines can be individually programmed to send DTMF 
(tone) or dial pulse signals.
DTMF / Dial Pulse Programming
Description
Each individual outside line can be programmed to be DTMF (tone) or dial pulse.
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed,...

2-64CO Line Group
Chapter 2 - Features and Operation
DTMF On/Off Time Operation
Description
The DTMF On/Off Time feature lets the installer select the DTMF On/Off Time on a 
system-wide basis. This lets the installer customize the system for certain applications that 
require more than the standard DTMF Time of 100ms on and 100ms off.
Programming Steps
1. Press the DTMF TIME OPERATION flexible button (FLASH 02, Button #6). The following 
message displays:
2. Enter a valid number (1-9) on the dial pad for...