Vodavi Starplus Triad S Installation Programming Manual

911 Feature2-5
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press Button #15 to designate the line for 911 use.
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds and...

2-6911 Feature
Chapter 2 - Features and Operation
The list remains available for review by pressing the 911 ALERT flexible button as necessary, 
until after the messages are deleted.
To delete logged 911 Alert messages:
An attendant uses the following steps to delete the messages on a system-wide basis.
1. Press the 911 ALERT flexible button to display the 911 call information for deletion.
2. Press FLASH to delete that message.
Enhanced 911 Integration
Description
The E911 feature integrates the system...

Account Code2-7
Chapter 2 - Features and Operation
Enhanced 911 Power Failure Station 
Description
The power failure signal is designed to be used with the normally open (NO) power failure 
leads from the Proctor unit connected to an SLT port or SLA device. When the leads close in 
power failure, this is detected as an off hook and 911 routing ceases to the Proctor unit. 911 
calls are sent via trunks other than those marked for 911 use until the power failure lead 
opens, which is detected as an on...

2-8Account Code
Chapter 2 - Features and Operation
Operation
When connected to an outside line call:
1. Press the preprogrammed ACCOUNT CODE button (feature code 627 - refer to “Flexible 
Button Assignment” on page 2-130).
2. Dial account code up to 12 digits. ( The other party does not hear the digits being dialed).

If account code is less than 12 digits, an [
] must be entered to return to the call.

If account codes are forced, the account code must be entered prior to dialing the 
outside number....

Account Code2-9
Chapter 2 - Features and Operation
Operation
Prior to placing an outside line call:
1. Press the preprogrammed ACCOUNT CODE button.
2. Dial account code up to 12-digits.

SINGLE LINE TELEPHONE
To enter an Account Code before a call:
1. Lift the handset.
2. Dial [627].
3. Dial the account code.
4. Dial [9] or CO Access code. Dial tone sounds.
5. Dial the desired number.
To enter an Account Code during a call:
1. Depress the hookswitch momentarily. Your call will be placed on executive...

2-10Account Code
Chapter 2 - Features and Operation
Figure 2-1:  Flash 31 Button Mapping
Related Information
Programming Steps
To enable or disable Verified Account Codes:
1. Press the VERIFIED ACCT CODES flexible button (FLASH 06, Button #3). The following 
message displays:
2. Enter 0 or 1 on the dial pad to enable/disable Verified Account Codes.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Verified Acct Codes are disabled.
To assign Verified...

Account Code2-11
Chapter 2 - Features and Operation
2. Press the ACCT CODE flexible button (FLASH 31, Button #1). Enter up to 12 digits
(0-9, *, #). [*] represents a do not care digit. The system ignores all digits after this digit 
when entering an account code. The [#] represents a single do not care digit.
3. Press the CLASS OF SERVICE flexible button (FLASH 31, Button #2). Enter a 2-digit Class 
of Service Number (1-7) that corresponds to Class of Service 1-7. The first digit represents 
Day COS and...

2-12Account Code
Chapter 2 - Features and Operation

SINGLE LINE TELEPHONE
To enter an Account Code before a call:
1. Lift the handset.
2. Dial [627].
3. Dial the account code.
4. Dial [9] or CO Access code. Dial tone sounds.
5. Dial the desired number.
Conditions
» Verified Account Codes allow use of an account code as a traveling Class of Service.
» If LCR is activated in the system and verified account codes are activated, the user must 
enter the account code before dialing the LCR code.
» When...

Account Code2-13
Chapter 2 - Features and Operation
Programming Steps
1. Press the INITIALIZE ACCT CODES flexible button (FLASH 80, Button #14). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
Print Verified Account Codes
Description
The Print Verified Account Codes command dumps the entire database as a permanent 
record which can serve as a hardcopy of the database. The system baud rate must match that 
of the printer or receiving device.
Figure 2-2: Verified...

2-14 Answering Machine Emulation
Chapter 2 - Features and Operation
Answering Machine Emulation
Description
When a call is sent to a voice mailbox, the station associated with that can press a 
preprogrammed button to listen to the caller leaving the voice mail message. If the mailbox 
owner decides to speak with the caller, the owner can press the preprogrammed button to 
be connected to the caller.
Two methods of notification are available, Ring Mode or Speaker Mode. The preprogrammed 
button type...