Vodavi Starplus Station User Guide

56 Group Listening
To erase a flexible button:
1. Press SPEED twice.
2. Press the flexible button to be erased.
3. Press FLASH. A confirmation tone will sound.
4. Press the ON/OFF button.
To check flexible button programming:
1. Lift handset.
2. Press SPEED, then dial [7] + [#].
3. Dial [2] to select the KEYBTN option.
4. Press the desired flexible button(s) to display programming 
for the button(s) on the LCD.
5. When finished, replace the handset.
Group Listening
All digital key stations have a...

Headset Mode 57
Headset Mode
A modular headset may be used by connecting the headset to 
the handset jack on the telephone (leaving the handset in 
place). The ON/OFF button on the Digital Telephone is used to 
initiate and end calls while using the headset.
To activate Headset Mode:
Dial [634] on the dial pad,
-or-
Press the preprogrammed HEADSET MODE button. The LED 
will light steady.
To deactivate Headset Mode:
Dial [634] on the dial pad,
-or-
Press the preprogrammed HEADSET MODE button. The LED...

58 Intercom
Intercom
Using an Intercom Button 
To program a Flexible Button as an Intercom Button:
1. Press the SPEED button twice.
2. Press the desired flexible button to program.
3. Dial [645] on the dial pad. A confirmation tone will sound. If 
an error was made during entry, an error tone will sound.
When intercom call rings a busy station (w/intercom btn):
1. The calling station receives ringback tone instead of busy 
tone. The called station hears muted or reminder ring and 
their intercom button...

Intercom 59
Answering an Intercom Call
Depending on the position of your intercom button signal 
switch, answer the intercom call as indicated:
H Mode (No LED) Handsfree Mode -- You will hear three bursts 
of tone and an announcement.
Reply handsfree or lift handset for privacy.
P Mode (LED Flashing) Privacy Mode -- You will hear three 
bursts of tone and a one-way announcement. The calling party 
cannot hear conversations in progress.
Lift handset or press ON/OFF to answer.
-or-
Position the H-T-P...

60 Intercom
To use Intercom Transfer with DSS Buttons:
1. Receive or make an intercom call using a DSS button.
2. Press the TRANS button. An intercom dial tone will sound.
3. Press the DSS button where to transfer the call.
4. Hang up (stations 1 and 2 will be connected).
Intercom Calls
To place an Intercom Call:
1. Press the DSS button of the party to be called (if 
programmed at your phone),
-or-
Dial the extension number.
(You will hear ringing if the called station is in the T mode; 
or three bursts...

Intercom 61
In the P mode (LED flashes ), you will hear three bursts of tone 
and one-way announcement. The calling party cannot hear 
conversations in progress.
Lift the handset or press the ON/OFF button to answer,
-or-
Press the H-T-P button to the H mode to reply.
In the H mode (No LED), you will hear three bursts of tone and 
an announcement.
Reply handsfree or lift the handset for privacy.

SINGLE LINE TELEPHONE
To place an intercom call:
1. Lift the handset.
2. Dial the intercom number. You will...

62 Keyset Mode
Keyset Mode
This feature allows you to determine the mode and baud rate 
of the optional CTI Module connected to your phone.
This setting is stored in back-up memory in the case of a power 
outage or system reset.
When telephone is set to AT command mode, these AT 
commands are supported.
Table 1: AT Command Modes
Mode Description
Inactive No CTI information is sent/received by the telephone.
ATD Modem Dialing Command -- The telephone will recognize the 
ATD and accept digits after the...

Last Number Redial 63
At an idle station:
1. Dial the Keyset Mode code [648] on the dial pad,
-or-
Press the preprogrammed KEYSET MODE button, the 
following displays:
2. Press [

] to scroll through the keyset modes.
3. Press [#] to scroll through the baud rates.
4. Press the HOLD button to save the desired entries.

ELECTRONIC TELEPHONE
Not applicable

SINGLE LINE TELEPHONE
Not applicable
Last Number Redial
The Last Number Redial (LNR) feature permits the automatic 
redialing of the last telephone...

64 LCR Operation
If that line is busy, the system will select another line 
from the same group and redial the number.
If no lines are available in the same group, you will 
receive a busy tone and can queue for a line.
If you preselect a line before activating LNR, the 
preselection will override the line used originally.

SINGLE LINE TELEPHONE
Not applicable
LCR Operation
To place an outside call when LCR is enabled in the system:
1. Dial [9] on the dial pad,
-or-
Press the preprogrammed LCR...

Loop Key 65
CO Line Queue Cancel
To cancel a Call Back Request:
1. Dial the CO Line Queue Cancel code [626] on the dial pad.
2. Replace the handset or press the ON/OFF button.
Loop Key
A station not having a direct appearance for a CO line will 
receive incoming CO calls and transferred CO calls under the 
LOOP button. Only one call at a time can be connected to a 
keyset on the LOOP button.
To make a Loop button:
1. Press the SPEED button twice.
2. Press the desired flexible button.
3. Dial [89].
4....