Vodavi Starplus Station User Guide

							56 Group Listening
To erase a flexible button:
1. Press SPEED twice.
2. Press the flexible button to be erased.
3. Press FLASH. A confirmation tone will sound.
4. Press the ON/OFF button.
To check flexible button programming:
1. Lift handset.
2. Press SPEED, then dial [7] + [#].
3. Dial [2] to select the KEYBTN option.
4. Press the desired flexible button(s) to display programming 
for the button(s) on the LCD.
5. When finished, replace the handset.
Group Listening
All digital key stations have a built-in speakerphone. You can 
use the speaker to monitor a call while using the handset to 
consult with the outside party. This enables other people in the 
room to listen to both parties in the conversation.
To activate Group Listening:
While conversing on the handset, press the ON/OFF button.
Both parties of the conversation can then be heard on the 
digital stations speaker. The speakerphone microphone is 
muted while the handset is off-hook.
To deactivate Group Listening:
While off-hook, press the ON/OFF button.
Group Listening is NOT available when the station 
is in the Headset Mode. 
						

							Headset Mode 57
Headset Mode
A modular headset may be used by connecting the headset to 
the handset jack on the telephone (leaving the handset in 
place). The ON/OFF button on the Digital Telephone is used to 
initiate and end calls while using the headset.
To activate Headset Mode:
Dial [634] on the dial pad,
-or-
Press the preprogrammed HEADSET MODE button. The LED 
will light steady.
To deactivate Headset Mode:
Dial [634] on the dial pad,
-or-
Press the preprogrammed HEADSET MODE button. The LED 
will extinguish.

SINGLE LINE TELEPHONE
Not applicable
While Headset mode is active, the ON/OFF button 
activates the headset and disables speakerphone 
and intercom call announce operation at your 
station.
To install the headset, see the Installation Manual.
Station must be programmed in database 
programming for headset operation before the 
flexible button can be programmed. 
						

							58 Intercom
Intercom
Using an Intercom Button 
To program a Flexible Button as an Intercom Button:
1. Press the SPEED button twice.
2. Press the desired flexible button to program.
3. Dial [645] on the dial pad. A confirmation tone will sound. If 
an error was made during entry, an error tone will sound.
When intercom call rings a busy station (w/intercom btn):
1. The calling station receives ringback tone instead of busy 
tone. The called station hears muted or reminder ring and 
their intercom button LED starts flashing at the incoming 
CO line rate. This indicates an incoming intercom call.
2. The called station can place the current CO call on hold by 
pressing the HOLD button,
-or-
Place the current intercom call on hold by pressing the 
HOLD button. The intercom call is placed on hold on the 
available intercom button.
3. The called station then presses the flashing intercom 
button to answer incoming intercom call. When answered, 
the following message displays on the called station LCD:
Sta XXX can be a programmed station name.

SINGLE LINE TELEPHONE
Not applicable
CALL FROM STA XXX
MMM DD YY HH:MM am
❑
Flex
Btn 
						

							Intercom 59
Answering an Intercom Call
Depending on the position of your intercom button signal 
switch, answer the intercom call as indicated:
H Mode (No LED) Handsfree Mode -- You will hear three bursts 
of tone and an announcement.
Reply handsfree or lift handset for privacy.
P Mode (LED Flashing) Privacy Mode -- You will hear three 
bursts of tone and a one-way announcement. The calling party 
cannot hear conversations in progress.
Lift handset or press ON/OFF to answer.
-or-
Position the H-T-P switch to the H mode to answer.
T Mode (LED On) Tone Mode -- You will hear repeated bursts of 
intercom tone ringing and HOLD button slow flashes.
Lift the handset or press the ON/OFF button to answer.
-or-
Position the H-T-P switch to the H mode to answer.
Intercom Transfer
To use Intercom Transfer without DSS Buttons:
1. Receive or make an intercom call.
2. Press the TRANS button. An intercom dial tone will sound.
3. Dial the desired station number.
4. When the second station answers, you are in a supervised 
transfer mode (first station is staged for transfer).
5. Hang up (stations 1 and 2 will be connected).
Use fea ture c o de 6 6 7 to  s el ec t a n H, P, o r T m o de for  8-
button digital telephones. Each use of this feature 
code acts as a rotary through the three options. 
						

							60 Intercom
To use Intercom Transfer with DSS Buttons:
1. Receive or make an intercom call using a DSS button.
2. Press the TRANS button. An intercom dial tone will sound.
3. Press the DSS button where to transfer the call.
4. Hang up (stations 1 and 2 will be connected).
Intercom Calls
To place an Intercom Call:
1. Press the DSS button of the party to be called (if 
programmed at your phone),
-or-
Dial the extension number.
(You will hear ringing if the called station is in the T mode; 
or three bursts of tone if called station is in H or P mode.)
2. Lift the handset or use the speakerphone after the tone 
bursts stop.
3. Hang up to end the call.
To answer an Intercom Call:
In the T mode (LED On), you will hear repeated bursts of 
intercom tone ringing and the HOLD button slow flashes.
Lift the handset or press the ON/OFF button to answer,
-or-
Press the H-T-P button to the H mode to reply.
Dialing a number in the numbering plan activates 
the telephone automatically. 
						

							Intercom 61
In the P mode (LED flashes ), you will hear three bursts of tone 
and one-way announcement. The calling party cannot hear 
conversations in progress.
Lift the handset or press the ON/OFF button to answer,
-or-
Press the H-T-P button to the H mode to reply.
In the H mode (No LED), you will hear three bursts of tone and 
an announcement.
Reply handsfree or lift the handset for privacy.

SINGLE LINE TELEPHONE
To place an intercom call:
1. Lift the handset.
2. Dial the intercom number. You will hear ringing if the called 
station is in the “T” answering mode or two bursts of tone if 
the called station is in the “H” or “P” positions.
3. Hang up to end the call.
To answer an intercom call:
Lift the handset,
-or-
If your SLT is equipped with a speakerphone, press the 
Speaker button to converse in a handsfree mode. 
						

							62 Keyset Mode
Keyset Mode
This feature allows you to determine the mode and baud rate 
of the optional CTI Module connected to your phone.
This setting is stored in back-up memory in the case of a power 
outage or system reset.
When telephone is set to AT command mode, these AT 
commands are supported.
Table 1: AT Command Modes
Mode Description
Inactive No CTI information is sent/received by the telephone.
ATD Modem Dialing Command -- The telephone will recognize the 
ATD and accept digits after the command.
AT H  o r  
AT H X
(X= 0 or 1)Modem On-Hook/Off-Hook Command -- ATH or ATH0 will 
force the telephone to go to the on-hook state from its current 
state. ATH1 will force the telephone to go to the off-hook state 
from it’s current state.
CKTU Command used with Wanderer (a cordless key telephone unit). 
The baud rate is not used in this mode; no change is necessary.
PC Phone CTI information used with Discovery Desktop and Discovery 
PCPhone software must be set to 4800 baud rate.
SPI Service Provider Interface -- Command used with TAPI 
applications such as Discovery Link 
						

							Last Number Redial 63
At an idle station:
1. Dial the Keyset Mode code [648] on the dial pad,
-or-
Press the preprogrammed KEYSET MODE button, the 
following displays:
2. Press [

] to scroll through the keyset modes.
3. Press [#] to scroll through the baud rates.
4. Press the HOLD button to save the desired entries.

ELECTRONIC TELEPHONE
Not applicable

SINGLE LINE TELEPHONE
Not applicable
Last Number Redial
The Last Number Redial (LNR) feature permits the automatic 
redialing of the last telephone number dialed on an outside 
line. Up to 24-digits can be stored. Outside line selection of the 
same line used is automatic.
To use Last Number Redial:
1. Press the SPEED button.
2. Press [#]. The last number dialed over an outside line is 
automatically redialed.
The system will automatically selectsthe original line used 
to place the call and redialsthe number.
INACTIVE 2400
MODE=

 SAVE=HOLD BAUD=# 
						

							64 LCR Operation
If that line is busy, the system will select another line 
from the same group and redial the number.
If no lines are available in the same group, you will 
receive a busy tone and can queue for a line.
If you preselect a line before activating LNR, the 
preselection will override the line used originally.

SINGLE LINE TELEPHONE
Not applicable
LCR Operation
To place an outside call when LCR is enabled in the system:
1. Dial [9] on the dial pad,
-or-
Press the preprogrammed LCR button.
2. Dial the desired telephone number.
3. Wait for an answer. Lift the handset or use the 
speakerphone to converse.
If all available lines are busy, remain off-hook for four 
seconds to automatically be queued onto LCR for an 
available line, then hang up.
To answer an LCR Queue Call Back:
1. When yourtelephone is signaled, answer the call.
2. The desired telephone number will be automatically 
redialed.
Only one LCR Queue Call Back request may be 
initiated by a station. When a second request is 
made, the first request is cancelled.
If the 911 feature is enabled, the LCR access code 
is 800 instead of 9. 
						

							Loop Key 65
CO Line Queue Cancel
To cancel a Call Back Request:
1. Dial the CO Line Queue Cancel code [626] on the dial pad.
2. Replace the handset or press the ON/OFF button.
Loop Key
A station not having a direct appearance for a CO line will 
receive incoming CO calls and transferred CO calls under the 
LOOP button. Only one call at a time can be connected to a 
keyset on the LOOP button.
To make a Loop button:
1. Press the SPEED button twice.
2. Press the desired flexible button.
3. Dial [89].
4. Press HOLD.
Mailbox Buttons
To program a station’s mailbox on a flexible button:
1. Press the SPEED button twice.
2. Press the desired flexible button to be programmed.
3. Dial the mailbox feature access code (460-467 = voice mail 
group 1-8; 468 = remote voice mail group).
4. Dial the VMID number. A confirmation tone will sound. If an 
error is made during entry, an error tone will sound.
Feature code 468 does not apply to Triad-S systems.
❑
Flex
Btn
❑
Flex
Btn