Vodavi Starplus Automatic Voice Processing Technical Manual

STARPLUS @ AVP TECHNICAL MANUALINSTALLATION
Load Defaults 
[M.BAT]This option erases all system information and returns the system
to its’ original settings. The following information is erased so be
careful with this option:
l Mailbox/Extension information
lPhone System Settingsflone Plan
When selecting this, five default class of services are loaded auto-
matically. Their definition is as follows:
00 
- (LEVEL 1) User type 1, max message length 300 seconds,
max message count 100, max retention 30 days,...

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
3.The editor screen will appear with the file contents shown...-
4.Use the arrow key to move to the 6 in the 64 entry and press>~
,?[DEL] twice to erase. Then modify the setting as follows:,:
l2 Ports should read -e32 (type 32)
l4 Ports should read -e64 (type 64)
l 6 Ports should read 
-e96 (type 96).
o8 Ports should read -el28 (type 128)
l12 Ports should read -el92 (type 192)
5.Press [CTRL-F2] to save the file and exit the editor.
6.Type [VODAVI] and press the...

STARPLUS @ AVP TECHNICAL MANUALINSTALLATION
4.Enter your company name at the sign in screen.
Make sure the spelling is correct as you only get one chance
to enter the company name.
5.Answer all of the questions as they appear on the screen.
Select modem type AT Compatible.
6.Enter a [X] when done with all the questions.
7. Type [C:] and then the [ENTER] key.
8.Type [CD\] and press the [ENTER] key.
9.Type [MD CCOPY] and press the [ENTER] key.
10. Type [CD\CCOPY] and press the [ENTER] key.
11. Type [COPY...

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
6.Using the up arrow key move the cursor to the line that starts
with PATH. Move the cursor to the end of this line and type
[C:\CCOPY].At this point your AUTOEXEC.BAT file should look similar to
the following example.
This is only an 
example._Your AUTOEXEC.BAT file may be
slightly different.
Q ECHO OFF
SET COMSPEC=C:\DOS\COMMAND.COM
VERIFY OFF
PATH C:\DOS;C:\VODAVI;C:\CCOPY 
_PROMPT $P$G
C:\SPAVP\d40drv -e64 -COCD\CCOPY
cc
CD\
VODAVI 1
7.Press and hold the...

STARPLUS @ AVP TECHNICAL MANUALINSTALLATION
500.5 SYSTEM
UPGRADES
A. PORT UPGRADESThis section describes the procedures involved in upgrading an
existing 
Starplus AVP. The base Starplus AVP system is a flexible
platform that can expand up to 12 ports and 15 hour storage ca-
pacity. Upgrades are divided into three types, port, storage, or
both.Port upgrades increase the line capacity of the 
Starplus AVP. This
is achieved by adding additional voice boards and updating the
software controller. The voice...

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
VOICE BOARD 
SElTlNGSThere are three jumpers and a DIP switch that need to be set on
the voice board. The jumpers are labeled JP7, 
JPl , and JP5.
Each is located near the bottom of the board just above the bus
connector. The DIP switch, labeled SW1 , located above the bus
connector, has four toggle switches.
lJumper JP7 is used to identify the terminating voice board
in your 
Starplus AVP system. This jumper must only be in-
stalled on one voice board in a...

STARPLUS @ AVP TECHNICAL MANUALINSTALLATION
lJumper JP5 is used to select the base memory address
that will be occupied by the voice board(s). The default set-
ting is almost always the best choice, because memory
paragraph 
DO00 is reserved for add-on hardware like the
Starplus AVP voice boards. However, there could be a
memory address conflict between the voice board(s) and
other add-on hardware (such as a tape drive controller, a
network card, etc.) in the 
DO00 paragraph. If there is a con-
flict,...

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
The following settings are provided as examples.
Switch 1 settings, board 1Address 
DO00Switch 1 settings, board 
2Address D200
Switch 1 settings, board 3Address D400
Multiple voice board installation, switch 1 settingsSOFTWARE INSTALLATION
When you upgrade your port capacity, you will need to update the
software controller via a set of disks that came with your upgrade
package.To install the 
Starplus AVP upgrade program, insert the StarplusAVP MASTER DISKETTE...

STARPLUS @ AVP TECHNICAL MANUALINSTALLATION
lBackup the existing hard drive. Refer to Appendix G for
backup procedures.
lRemove the existing hard drive.
lInstall the new hard drive.
lRestore the backed up information to the new hard drive.
Refer to Appendix G for restore procedures.
HARD DRIVE REPLACEMENT
1. Remove the enclosure.
2.Locate the ribbon cable and power connector on the hard
disk and disconnect them. Be sure to make note.of the polar-
ity of the connector so it may be reconnected the same...

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
3.Follow the software procedure described in this section.
SOFTWARE INSTALLATION
When you upgrade your port and hour capacity, you will need to
update the software controller via a set of disks that came with
your upgrade package.
To install the 
Starplus AVP upgrade program, insert the StarplusAVP MASTER DISKETTE DISK I into the floppy disk drive. Make
sure that the root directory of C drive is displayed on your monitor:
c:\
1.Close the drive door and type:...