Vodavi Starplus Automatic Voice Processing Technical Manual

STARPLUS @ AVP TECHNICAL MANUALINSTALLATION
SECTION 500
INSTALLATION500.1 INTRODUCTIONNew 
Starplus AVP systems come with the liardware pre-config-ured and all software pre-loaded onto the hard drive. All that is re-
quired is to connect the monitor, software controller, and the
keyboard. These are all external connections and do not require
the unit to be disassembled. Once these external connections are
made you can power the system up and begin to configure it. The
Starplus AVP software contains...

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
500.2 SITESelection of a suitable location is the most basic, yet most critical
REQUIREMENTSconsideration in the installation of the Starplus AVP system. The
following factors should be considered when choosing an appro-
priate location for equipment 
.installation:
lAmple space must be allowed to remove the cabinet
cover, to access assemblies and cards within the cabinet
and allow space for connections to the unit. There must be
room to insert floppy disks...

STARPLUS @ AVP TECHNICAL MANUALINSTALLATION
overhead lines. Install a transient AC protection device if
the system is installed in a manufacturing area where mo-
tor driven machinery and such is installed.
lProtect the equipment against accumulated static electric-
ity which can damage’sensitive electronic circuitry in the
enclosure. If the site is at a high altitude or in a dry climate,
humidifying the area may be necessary to correct static
electricity problems.
500.3 NEW SYSTEM
HARDWARE
INSTALLATION...

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
B. INSTALLING THE
SOFIWARECONTROLLERThe controller resembles a standard male/female parallel 
connec-tor and simply plugs into the parallel port on the back of the PC. If
you have a parallel printer or other device attached to that port,
temporarily remove it, install the controller, and then reinstall the
device on the back of the controller.
IMPORTANT! The software controller is designed to recognize
the type and version number of the 
moduks cukently...

STARPLUS @ AVP TECHNICAL MANUALINSTALLATION
If you have RJ-14 terminations for your phone lines then you need
a pair of standard 
4-wire modular cables.
2.Connect the modular connectors to any of the jacks on the
board. The cable should slide in easily and snap in place
when the connection is made.
AUDIO Board(s) Up to 34 Port Voice Board
2 Port Voice Board
~Pot-ts 1 & 2Upper modular connector
-1P0r-t~ 3 & 4 Lower modular connector
Uses RJ14 type wiring
Black/Yellow Port 2
Green/Red Port 1Black/Yellow...

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
500.4 NEW SYSTEM
SOFTWARE
INSTALLATION
A. INITIAL SET UPOnce the hardware items are‘installed, you are ready to power the
system up and configure the basic items needed for integration.
1.Push the power switch on the front of the enclosure to the
ON (depressed) position.
The system should go through its power up procedure and
load the system software. You should be 
tit the main screen
showing the lines and current status window.
2.Write down the serial number...

STARPLUS @ AVP TECHNICAL MANUAL
INSTALLATION
A listing of the 
Starplus phone systems that may be loaded will ap-
pear. These items are lettered G-K to represent the various 
Star-plus phone systems that integrate with the 
Starplus AVP.
5.Enter the letter (G-K) that represents the phone system set-
tings you wish to load.
6.Press any key if you are sure this is the phone system you
wish to load. Press [CTRL-C] to abort the operation. Once
the settings are loaded you will be returned to the utility...

.sTAF&lJS @ AVP TECHNICAL MANUAL
The system will load the maintenance program and prompt you
for a password.
ilAINT ~525100v+3.10aConfigurationIlodulesReportsUtilitiesHouseKeepingII
IIi ._ mm_. a-lEsc: back a menuR&urn: se1+stl : moves barBackSpace: edits
1.Press the [ENTER] key. This is the default password.
The highlight bar should appear on the configuration menu item.
2.Press the [DOWN ARROW] or [ENTER] key to pull down the
menu.
3.Highlight the Environment item and press [ENTER].
4.Highlight the...

6.Press the [ESC] key twice.
7.Highlight the Registration item and press [ENTER].
8.Highlight the Edit Registration item and press [ENTER].
9. Complete the registration form.
You may use the arrow keys, backspace, and enter keys to
edit the registration-form.
VAINT sn525100
ConfigurationnodulesReportsUtilitiesv+3.10aHouseKeepingI
Company :street :
City :
state :
Zip :
Phone :
Number of Lines :
Number of Ext. :
PBX nanufacturer :
PBX Node1 #Bought SPAVP from:
Publications read :
Press ESC when done.
I-, ....

INSTALLATIONSTARPLUS @ AVP TECHNICAL MANUAL
COS 
SE-ITINGS00 
- (LEVEL 1) User type 1, max message length 300 seconds,
max message count 100, max retention 30 days, use message
waiting lamps, lists personal.
01 
- (LEVEL 2) User type 1, max message length 300 seconds,
max message count 100, max retention 30 days, ignore message
waiting lamps, lists personal.
02 
- (LEVEL 3) User type 2, max message length 180 seconds,
max message count 50, max retention 15 days, use message
waiting lamps, lists...