Vodavi Starplus Automatic Voice Processing Technical Manual

CONFIGURATIONSTARPLUS @ AVP TECHNICAL MANUAL
l Dialing Prefixes
l Feature Prefixes
l Hang-Up Detection
This is done in conjunction with the Utility menu procedure.
Please follow section 500, Initial set up for the entire procedure.
To select a phone system configuration:
1.Highlight the Load Phone System sub menu and press [EN-
TER].
A file, with descriptively recognizable names, will be listed.
2. Highlight either, 
2448EX.pbx, 96EX.pbx, 1428.pbx,
2856.pbx, or SPX.pbx and press the [ENTER] key.
rWINT...

STARPLUS @ AVP TECHNICAL MANUALCONFIGURATION
The 
Starplus AVP Dialing Prefix screen is presented
MAINT sn525100v+3.10aConfigurationNodulesReportsUtilities1HouseKeepingIDialing Prefixes
Enter the numbers that are dialed
Phone Sy to 
access an internal or externalline.If no number is needed, leave
Load Pho field blank.ESC exits and savesSave Pho changes.
internal call:
local call :
long distance:
after dialing:
Screen contents are defined as follows:
n Internal Call: enter the prefix you have to dial to...

CONFIGURATIONSTARPLUS @ AVP TECHNICAL MANUAL
If you loaded from the Vodavi menu, a 
Starplus telephone system,
these feature prefixes were automatically set up for you. These
should not be changed. The characters 
& = flash-hook, 8 = exten-
sion number, and the comma 
[,I = pause. Screen contents are de-
tailed below:
IIRINT sn525100ConfigurationtlodulesReportsUtilitiesu+3.10aHouseKeepingFeature Prefixes
Hangup Detection
Phone System Name
Load Phone Settings
Save Phone SettingsIf the feature is not...

STARPLUS @ AVP TECHNICAL MANUALCONFIGURATION
n Transfer Outside: This is a flash hook or tone command
that transfers a call to an outside number.
n Set Message Waiting: This command turns the message
waiting light “On” for any extension that has a message
waiting light. Note that not all phone systems support this
feature. If your system does have message waiting indica-
tion, it must be accessible through DTMF. In other words,
by dialing a sequence of numbers from a single line tele-
phone, you can turn...

CONFIGURATIONSTARPLUS @ AVP TECHNICAL MANUAL
After determining the appropriate disconnect method, select 
Hana-up Detection in the Phone System sub menu. The Set Hang-up 
vType sub menu will be presented. Select Manually to display the
Manual Hang-up Detection screen.
MAINT ~525100v+3.10aConfigurationnodules-ReportsUtilitiesHouseKeepingRegistration
Environment
ICommon values are 5 to 7. Press
ESC to 
saw and exit.
Tone Interval :Off 0 
setsSilence Interval:On 10 setsRe-Order Tone2 Off
tl:moves...

STARPLUS @ AVP TECHNICAL MANUALCONFIGURATION
F. AUTOMATIC
DETECTIONIf you wish you can have 
Starplus AVP determine the appropriate
settings for hang-up detection. Select Automatic from the Hang-up
Type sub menu and the Automatic Hang-up Detection screen will
be presented.
NAINT sn525100v+3.10aConfigurationModules ^ReportsUtilitiesHouseKeepingThis item is only used when connecting the 
Starplus AVP to a non
Starplus phone system.
1.Using a telephone, dial the extension of the line connected to
the...

CONFIGURATIONSTARPLUS @ AVP TECHNICAL MANUAL
SHOW CURRENT FILE
1.To determine the current ConfigSys file configuration move
the highlight bar to Show Current File. If it already exists it
should read:
MAINT sn525100v+3.10aConfigurationllodules-ReportsHouseKeeping1UtilitiesIEnvironment
CONFIG.SVS_BREAK=ONSHELL=C:~DOS\COlltlAND.CO~ /P /E:256DEUICE=C:\EnnDRUR.SYSFILES= 30BUFFERS = 16
I1
. _I.IPress finy Key To Continue.
Files 
= 30
Buffers = 16 (These settings may be different depending upon
port size)...

STARPLUS @ AVP TECHNICAL MANUALCONFIGURATION
610.2 SYSTEMThe System menu should not be confused with the Phone System
menu. The Phone System menu defines the interface between
Starplus AVP and your specific type of phone system. In the Sys-
tem menu, you define the environment within which the phone sys-
tem operates. The System menu includes the following submenus:
A. CALL OUT LINES
0 Call Out Lines
l Logging
l Blockage Lines
.
lRR & FF Speed
l Other Settings
l Input Lengths
l Work Hours
This section of...

CONFIGURATIONSTARPLUS @ AVP TECHNICAL MANUAL
The screen and all its’ entries are shown below.
tlAINT sn525100Configuration
L,tlodulesReportsUtilitiesu+3.10aHouseKeepingCall-Out 
Lines---------Outdialing is used for features
like message notification, polling,
and housekeeping.
SPRUP uses line
groups to control which line will gel
used.Group numbers range from 1 to3.R value of 0 will keep the line
from being used as call-out.
Use the keys 0 through 9 to set
how each 
line will get-used.
Press ESC to save...

STARPLUS @ AVP TECHNICAL MANUALCONFIGURATION
1.To turn logging “on” move the highlight bar to the device that
you want to direct the data to, and press [ENTER]. The Enter
key acts like a toggle. Pressing Enter a second time turns
the device “off”. A check mark next to a device indicates that
it is turned “on”.Note that in order to generate reports, you 
MUST direct the log-
ging output to the File. We recommend that you do this unless
disk space is in critically short supply. Output to the disk is...