Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

infinite n Digital SystemsTF NO: 53-.
Direct Inward Dialing (Cont’d)
Programming Steps:
1.Press FLASH and dial [24]. The following message will be shown on the display:
Where:
S 
= Station Board (KT12)
C 
= CO Line Board (CO12)/DlD
D 
= DTMF/Sta Combo Card
E 
- TIE Line Interface Board (TIE)T 
- Tl Trunk card
##- Blank (unused card slot)
- 2. The buttons 1 through 18 indicate peripheral card slots 1 through 18. When the Flexible Card Assignments
program is initially entered, Flex Button 
#l LED will be...

infinite ” Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
4.Press the HOLD button to complete the entry. Confirmation tone will be heard and the display will now update.
NOTE: 
Affer the card slots have been re-arranged, the system MUST be reset for full activation of the database
programming to take effect.
Default: The system defaults to a configuration that designates peripheral slots 1,2,3 and 4 for Station boards,
peripheral slots 
5,6,7 and 6 for CO boards, and peripheral slots 9, 10, 11...

infinite m Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
A. Direct Inward Dialing (DID) Table Programming:
The buttons on the digital terminal are defined as shown below when entering the DID programming area:
1.Press FLASH and dial 1441. The following message is shown on the display phone:
Where:
- RRR- Route Number (000-199)
- ###I DID Number (Directory W from C.O.) (7 digits)
- n..n- Name Assigned to DID Number (8 characters)
To program the Route Number:
1.The top left button (ROUTE) in the...

Infinite n Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
To program the DID Number:
1.Press the NUMBER Button (Button #2) in the flexible button field for programming the DID Number.
2.Enter the DID Number to be associated with a three-digit Route Number (009199). Up to 7 digits can be
entered. By default, only the last three digits will be used for routing. Thii is determined in Flash 45. (Refer to
Page 8).
3.The display will show the DID number as it is entered. Press the HOLD button to save...

infinite n Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
To erase a DID Table entry:
1.Press the CLEAR ENTRY Button (Button #4) to clear an entire Phone Number, Name and Route from the DID
Table. Press the HOLD button to save the entry. Confirmation tone will be heard and the entry cleared.
To change to a different DID Route:
1.Press the UP Button (Button #18) to advance to the DID Route Number.
OR
2.Press the DOWN Button (Button #19) to go back to a previous DID Route Number.
Default:By...

inttnite m Digital Systems
Direct Inward Dialing (ConY)
B. Direct Inward Dialing Parameters:TF NO: 53
The buttons on the digital terminal are defined as shown below when entering the DID programming area:
1.Press FLASH and dial [45J. The following message is shown on the display phone:
To program the number of DID digits:
1.Press the DIGITS Button (Button #l) in the flexible button field for programming the number of digits the system
will look at for routing purposes. The following message is shown on...

infinCfe ” Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
Default: By default, the type of DID Signaling is set for wink
To change the Wink Timer:
1.Press the WINK TIMER Button (Button #3) in the flexible button field for changing the Wink Timer settings. The
following message is shown on the display phone:
2.Enter a three-digit value on the dial pad which corresponds to 100-300...

infinlfe ” Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
C. 
InNalization of DID Tables:
Description:This section describes the procedures and steps necessary to initialize the system database returning 
any
programmed data to 
its original or default value. The entire system database may be initialized or various portions
of the database may be individually initialized. In addition to initialization of the entire database, a system reset
(Button 
#20) command is also included in this section...

infinite m Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
If the DID Timers need to be initialized:
1.Press the DID-TIE TMRS Button (Button #14). The following message will be shown on the display phone:
3.To initialize the DID Timers, press the HOLD button. Confirmation tone will be heard.
Vcdavi bmmunicetions Systems83DOE.&ll@WDrive
Page 16 of 27
saadak,k8960TF NO. 53w4 4434ow 

Infinite ” Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
D. Printing of DID Tables:
Description:
This section describes the procedures and steps necessary to print Data Base Parameters and various portions of
the system.
The buttons on the key telephone are defined as shown below when entering the Print Data 
Bass Parameters
programming area.
With a printer connected to the RS-232C port (Port 
#3) on the Backplane I/O Expansion Module, the currently stored
customer database can be printed or...