Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

in$initem DVX I’STATION ATTRIBUTES PROGRAMMINGDigital Key Telephone System
PAGE 
“B” STATION ATTRIBUTES (Cont’d)
J.Flexible Button Programming
Programming Steps
1.Press the BUTTON ASSIGN flexible button(Page B, Button 
# 10). The following mes-
sage is shown on the display phone:
2.Enter the two-digit button number [BB] tobe programmed followed by the desired
button function as follows:
where: BB= Button number (0 l-24)
MULTI: To assign a button as a multi-function
button (user programmable) enter:BB [0]...

inf~nitem DVX I’Digital Key Telephone System
STATION ATTRIBUTES PROGRAMMING
PAGE 
“B” STATION ATTRIBUTES (Cont’d)Flexible Button Programming (Cont’d)
Programming Steps
UNASSIGN: To unassign a button, enter:BB 
[#] HOLD
If SLT stations are to be programmed for 
Off-
Hook Preference, it is necessary to program the
desired CO line, or CO line group, the SLT is to
access when going off-hook.To assign a CO Line for a SLT with Off-Hook
Preference, enter:00 [ 
11 LL HOLD (LL= CO Line 01-48)
To assign a CO Line...

infinitem DVX I’STATION ATTRIBUTES PROGRAMMINGDigital Key Telephone System
PAGE 
“B” STATION ATTRIBUTES (Cont’d)
K. Display Flexible Buttons
Programming Steps
If the flexible buttons are to be viewed:
1.Press the DISPLAY BUTTONS flexible but-ton (Page B, Button 
#17). The program-
ming assignment on four buttons will be
displayed starting with the lowest button
number. With each sub-sequent depres-
sion of the DISPLAY BUTTONS button, thenext four buttons will be displayed. The
following message is shown...

PAGE “B” STATION ATTRIBUTES (Cont’d)
730.3DIGITAL DATA INTERFACE UNIT
(DDW
Programming StepsTo program a Digital Data Interface (DDIU)
unit:a. Press FLASH and dial 
1511. The following
message is shown on the display phone:
Where:
- WWW = Station Number (100-195)
- XXXXX= Baud Rate
- Y= Data Parity
- Z= Data Stop Bits
b. Enter the three-digit station number of the
DDIU unit.c. Press the HOLD button to save the entry.
The display will now update.
A. Baud Rate Options
Programming Steps1. Press the BAUD...

infinitem DVX m
STATION ATTRIBUTES PROGRAMMINGDigital Key Telephone System
Digital Data Interface Unit 
(DDIU) (Cont’d)B. Character Length Option
Programming Steps
Description1. Press the CHARACTER LENGTH flexible
button (Button 
#2).
2.Enter a one-digit number for the character
length of the digit string.
- [8] = 8 character length
- [9] = 9 character length
3.Press the HOLD button to save the entry.Confirmation tone is heard and the dis-
play will now update.CHARACTER LENGTH: Eight bit characters
are...

inJinitem DVX I’Digital Key Telephone System
STATION ATTRIBUTES PROGRAMMING
PAGE “B” STATION 
ATIXIBUTES (Cont’d)
730.4FLEXIBLE PORT ASSIGNMENT
FEATURE
Programming StepsIf the Station numbers need to be relocated to
different ports:a. Press FLASH and dial 
[52]. The following
message is shown on the display phone:
b.The buttons 1 through 8 indicate cards 1
through 8. When the relocation program is
initially entered, Button # 1 will be lit indi-cating that the user is programming the
Station numbers on...

infhitem DVX I’
Digital Key Telephone SystemTABLE OF CONTENTS FOR SECTION 740
SECTION 740
740.1740.2
740.3ICLID PROGRAMMING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .749-l
INTRODUCTION...................................................................................
.740- 1
A.Calling Number/Name Display..................................................
.740- 1
B.Incoming Number/Name for...

inznitem DVK I’Digital Key Telephone System
ICLID 
PROGRAMMlNG
SECTION 740
ICLID PROGRAMMING
740.1INTRODUCTION
Thisfeature is available with optional soft-
ware. The ICLID (Incoming Calling Line IDen-
tification) feature has been added to the 
infiniteDigital Key Telephone System. However, in
order for this feature to operate properly, it
must be activated from the central office so that
the numbers or name, if available, of the callingparty will be delivered over the individual tip
and ring of the CO...

ICLID PROGRAMMINGinJinitem DVX I’Digital Key Telephone System
2. Review next item in this
table entryMUTE
3. Step to next table entry.HOLD
4. Delete this table entry.FLASH ’
6. Exit table review function.ON/OFF
7. Step to previous table entry.TRANS
8. Call Back.SPEED
’ Only the 1st Attendant station can delete an
entry from this table.740-2
Issue 1, February 1994