Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

STATION ATTRIBUTES PROGRAMMINGinjinitem DVX I’Digital Key Telephone System
PAGE “B” STATION ATTRIBUTES (Cont’d)
730.2PAGE “B” INTRODUCTION
Programming StepsDescriptionIf the system is in the programming mode,
continue using the program codes. If starting toprogram here, enter the programming mode.
Refer to 700.2, Program Mode Entry (Key
Station).
If station features are to be changed:a. Press FLASH and dial 
[50]. The following
message is shown on the display phone:This section describes the steps and...

infhiteTM DVX I’Digital Key Telephone System
STATION 
A’ITRIBUTES PROGRAMMING
PAGE 
“B” STATION ATTRIBUTES (Cont’d)
A. Station Identification
Programming Steps1. Press the STATION ID flexible button
(Page B, Button # 1).To program the Station ID for a Digital Termi-
nal:
1.Dial a [0] on the dial pad.
2.Press the HOLD button to save the entry.Confirmation tone is heard and the dis-
play will now update.
To program the Station ID for a DSS/DLS Con-sole with Map 1, Map 2, Map 3, or Map 4:
Programming...

STATION ATTRIBUTES PROGRAMMINGin.nitem DVX InDigital Key Telephone System
PAGE 
“B” STATION ATTRIBUTES (Cont’d)
Station Identification (Cont’d)
To program the Station ID for a SLT or OPX
Station:
Programming StepsDescription
1.Dial a [ 51 on the dial pad.SLT/OFF PREMISE EXTENSION (OPX): This
2.Press the HOLD button to save the entry.external module provides the interface for oneConfirmation tone is heard and the 
dis-long loop (OPX) single line telephone (2500
play will now update.type) extension. This...

infkiteTM DVX I’Digital Key Telephone System
STATION ATTRIBUTES PROGRAMMING
PAGE 
“B” STATION ATTRIBUTES (Cont’d)
Station Identification (Cont’d)
To program the Station ID for a Relay/Sensor
Module:
Programming Steps
1.Dial a [7] on the dial pad.
2.Press the HOLD button to save the entry.Confirmation tone is heard and the dis-
play will now update.
To program the Station ID for a Digital Data
Interface box 
(DDIU):
Programming Steps
1.Dial a (81 on the dial pad.
2. Enter the three-digit associated...

STATION ATTRIBUTES PROGRAMMINGinJinitem DVX I*Digital Key Telephone System
PAGE 
“B” STATION ATTRIBUTES (Cont’d)B.Station Class of Service (COS)
Programming Steps
1. Press the CLASS OF SERVICE flexible
button (Page B, Button 
#2).
2.Enter a two-digit Class of Service entry asfollows:
l
1st digit is day COSl 2nd digit is night COS
The six classes of service are:
- [l] = unrestricted
- [2] = governed by Table A
DescriptionCLASS OF SERVICE. Each stations must be
assigned a certain COS for day mode...

infInite” DVX I’
Digital Key Telephone SystemSTATION ATTRIBUTES PROGRAMMING
PAGE 
“B” STATION ATTRIBUTES (Cont’d)
C. Speakerphone/Headset Programming
Programming Steps1. Press the SPEAKERPHONE flexible but-
ton (Page B, Button 
#3).
2.Enter a one-digit number on the dial pad
between 0 and 2 to identify the speaker-
phone operation.
- [0] = works as normal speakerphone.
Full speakerphone capabilities on
both CO lines and Intercom.
-[ l] = Speakerphone enabled for intercomcalls only. Speakerphone...

STATION ATTRIBUTES PROGRAMMINGinfinite?‘“l DVX I’Digital Key Telephone System
PAGE 
“B” STATION ATTRIBUTES (Cont’d)E. Paging Zone(s) Programming
Programming Steps
1.Press the PAGING ZONES flexible button
(Page B, Button 
#5).
2.Enter a one-to-four digit number to pro-
gram paging zone(s).
- [0] = no zone (no pages received)
- [l]=Zonel
- [2] = Zone 2
- [3] = Zone 3
- [4] = Zone 4
3.Press the HOLD button to save the entry.Confirmation tone is heard and the dis-
play will now update.
DescriptionPAGING...

infinitem DVX I’
Digital Key Telephone SystemSTATION ATTRIBUTES PROG-GPAGE “B” STATION ATTRIBUTES 
(Cont’d)
F.Preset Call Forward Programming
Programming Steps
1.Press the PRESET FORWARD flexible but-ton (Page B, Button 
#6).2. Enter a three-digit number to determine
the destination where calls are to be
routed when the preset forward timer ex-
pires.
Valid 3 
digit destinations are:
- [020-0991 = System Speed Bins 20-99
for off-net forwarding
- [ 100-1951 = Station Numbers
- [440-4471 = Voice Mail...

STATION ATTRIBUTES PROGRAMMINGinfznite” DVX I’Digital Key Telephone System
PAGE 
“B” STATION ATTRIBUTES (Cont’d)
G.CO Line Group Access
Programming Steps
1.Press the CO LINE GROUP ACCESS flex-
ible button (Page B, Button 
#7).
2.Enter up to seven digits (0, or l-7) for the
outside line groups the station will have
access to.
- [0] = no access
- [l] = access to Group 1, Code 9 or 81
- [2] = access to Group 2, Code 82
- [3] = access to Group 3, Code 83
- [4] = access to Group 4, Code 84
- [5] = access to...

infbitem DVX I’Digital Key Telephone System
STATION ATTRIBUTES PROGRAMMING
PAGE “B” STATION ATTRIBUTES (Cont’d)
I.Off-Hook Preference Programming
Pro@arnming Steps
To program a station for Off-Hook Preference;1. Press the OFF-HOOK PREF flexible but-
ton (Page B, Button 
#9). The following
message is shown on the display phone:
2.Enter the two-digit button number (0 l-48)or (00) to indicate no specific button is
preferred. 
SLTs use 01 to enable or 00 to
disable.
3.Then, enter either 0 or 1 where:
- [0] =...