Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

CUSTOMER DATA BASE PROGRAMMINGinfinite~ DVX I’Digital Key Telephone System
Table 700-l Default Values
.FEATURE
No-Answer Recall Timer
No-Answer Retry TimerGuaranteed Message Timer
UCD GROUP 
PROGlMMMING:UCD Groups 550-557
Alternate UCD Group
Overflow Assignment
Announcement Table(s) Entries
Select Page A
Select Page BUCD Groups (l-8)
Select Page A
Select Page BUCD TIMERS:
Ring Timer
MIT Timer
Over Flow TimerWrap-Up Timer
No-Answer Recall TimerNo-Answer Retry 
Timer
UCD RAN Announcement Tables
PC/ACD*...

infrnitem DVX InDigital Key Telephone System
CUSTOMER DATA BASE 
PROGRAMMlNGTable 700-l Default Values
FEATURE
VM Leave/Retrieve Disconnect TablesVM In-Band Digits
VM ID on Incoming CO CallsAllow Call Forward to Voice Mail
ALLOW/DENY 
& SPECIAL TABLES:
Allow Table A
Deny Table AAllow Table B
Deny Table B
Special Table 1
Special Table 2
Special Table 3
Special Table 4
Area Code for Special Table 1
Area Code for Special Table 2
Area Code for Special Table 3Display Tables
LCR PROGRAMMING:
3-Digit Routing...

CUSTOMER DATA BASE PROGRAMMINGinfznite” DVX I’Digital Key Telephone System
Table 700-l Default Values
Print System Parameters
Print CO Line Attributes
Print Station Attributes
Print CO/Station Port ParametersPrint Exception Tables
Print System Speed
Print LCR Tables
Print Entire System DatabasePrint 
ICLID* Parameters
Print Directory Dialing Table
Print Hunt Group ParametersPrint ACD* or UCD Group Parameters
Print VM Group ParametersAbort PrintingFEATURE
Init VM Group Parameters
System ResetPRINT DATA...

inflnitem DVX I’Digital Key Telephone System
CUSTOMER DATA BASE 
PROGRAMMlNG
To enter the program mode:a. Press ON/OFF button. (optional) LED
lights and intercom dial tone is heard.b. On the dial pad, press the asterisk 
(SC)
twice.
c. On the dial pad, enter the digits 
[3][2][2][6]
(DBAM)*. Confirmation tone is heard.* This is a default setting. However, it may be
changed after entering programming.
d. The ON/OFF button LED is lit. The systemis ready to program.
Other telephones connected to the system...

CUSTOMER DATA BASE PROGRAMMINGinfinite” DVX InDigital Key Telephone System
700.6CUSTOMER DATA WORKSHEETS
Before any attempt at programming is made, itis strongly recommended that customer data
worksheets be prepared (Refer to Appendix A).
These worksheets should become part of the
permanent record of customer programming.
Refer to the following sections when preparing
the worksheets.
700.7DATA BASE FIELDS
The data fields are used to set system timers,
determine central office line features and...

infznitem DVX InDigital Key Telephone System
CUSTOMER DATA BASE PROGRAMMING
3.Press the [Enter] key on the PC. The following
display will be seen on the Personal Com-
puter monitor.4896 Digital Key-System
Eng. Ver. 
0.071F DATE: 06/09/93 TIME: 13:12:59ENTER PASSWORD:
4. Enter the password 
[VODAVI], and press
the 
m key again. Proper entry of the
password will result in the ADM> prompt.Proceed with programming referring to
Figure 700- 1 for terminal characters that
represent the 
keyset buttons. By...

CUSTOMER DATA BASE PROGRAMMINGinfinite” DVX I’Digital Key Telephone System
t
22.3~DIGIT~ROUTE~TABLE
23.6-DIGIT_ROUTE_TABLE (table entrv)
24.EXCEPTION-CODE-TABLE
25.ROUTE-LIST-TABLE (table entry)
26.INS/DEL_TABLE (table entry)
27.
DAILYSTART-TABLE
28.WEEKLY START TABLE
29.ROUTE-FOR-555- 12 12
30.SYSTEM-SPEED-BIN
31.STA-SPEED-BIN (station 100thru
195)
32.SPEED-DIR (directory entry)
33.ICLID-TRANS-TBLE (trans table
entry)
34.ICLID-UAC-TABLE (uac table entry)
35.SPECIAL-TABLE
Forward and backward...

inflnitem DVK I’
Dig&d Key Telephone SystemSECTION 710
710.1710.2
710.3
710.4TABLE OF CONTENTS FOR SECTION 710
SYSTEM PARAMETERS PROGRAMMING
...................................710-l
SYSTEM TIMERS..................................................................................710-l
A. System Hold 
RecaII Timer..........................................................710-2
B. Exclusive Hold 
RecalI Timer.......................................................710-2
C.Attendant RecaII...

infinite” DVX I’Digital Key Telephone System
710.5
710.6
710.7
710.8
710.9
710.10
710.11710.12
710.13
710.14
710.15
710.16
710.17
s
D.Message Waiting......................................................................710-23
ATI-ENDANT STATION ASSIGNMENT..................................................7 lo-24SYSTEM TIME AND DATE...................................................................710-24
PBX DIALING CODES..
.......................................................................710-25...

infhite” DVX I’Digital Key Telephone System
SYSTEM PARAMETERS PROGRAMMING
SECTION 710SYSTEM PARAMETERS 
PROGRAIMMING
710.1SYSTEM TIMERS
Programming StepsIf the system is in the programming mode,
continue using the program codes. If starting toprogram here, enter the programming mode.
Refer to Sec. 700.2 , Program Mode Entry (Key
Station).DescriptionThis section describes the procedures and
steps necessary to program system timers.
The buttons on the digital terminal are defined
as shown below when...