Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

infrnitem DVX I’Digital Key Telephone System
INSTALLATION
PCDDIU1
 GND
TD2If------b. 2RD
IiD p-1 3TD
SG77SG
RTS 4
b 4RTS
CTSS45 CTS
DTR 
20b PODTR
DSRG16 DSR
DCDB1BDCD
RI 22422 RI
TXCLKi54ISTXCIKRXCLKi74I’IRXTLKComputer to Phone Cable
To establish a connection to any idle data port:
1.A user with an associated DDIU dials thestation number of the DDIU or the group
access number of the group that the DDIUhas been inserted into or presses a DSS
button representing the DDIU. The digital
key system will then...

INSTALLATIONinfznite” DVX I’Digital Key Telephone System
Table 500-6 SMDR Printout
The SMDR feature provides detailed records of all outgoing and/or Incoming, long distance only
or all calls. The SMDR Qualification Timer determines the length of time that is needed to
determine a valid SMDR call for reporting purposes. By default, this timer is set to 30 seconds
and is variable from 00 to 60 seconds in 1 sec. Increments. This feature is enabled or disabled insystem programming. By default, SMDR is not...

inrtrzite” DVX ‘I1Digital Key Telephone System
SECTION 600
SYSTEM CHECK-OUTSYSTEM CHECK-OUT
600.1INTRODUCTION
Prior to actual power up and initialization, the
inJntie Digital Key Telephone System should bechecked over to avoid start up delays or im-
proper loading. A step-by-step checklist is pro-
vided for this purpose.
600.2PRELIMINARY PROCEDURES
1.Make sure that the Basic Key Service Unit(BKSU) is properly grounded.
2. Verify that all 
PCB’s are firmly plugged
into the correct card slot positions or...

,b Lxx!i
VO3AVlTECHNICAL FACT NOTICE
infinite’” Digital Systems
TF NO: 46a
5/l at94Direct Inward Dialing (DID) Feature
for the infinite
TM DVX ” Digital System
This hardware enhancement is supported with Software Version 
2.3G or higher. The Database Upload/Download
procedures must be used to properly install this software.
Description:
aThe 4x8 Direct Inward Dialing (DID) Interface Board provides for One-Way Direct access to specific stations on
specific DID lines from the public telephone network,...

infinite TM Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
Installation of DID card:
1.The 4x8 DID Interface Board can be installed in any card slot on the infinite DVX ” Digital system.
2.Connect the provided -48~ assembly cable to the J6 connector on the 4x8 DID Interface Board. Pin 1 of
J6 is chassis ground. Pins 2 and 3 are the 
-48~ power supply.
4x8 DID Interface Board RJ-14 Modular Jack 
PinoutsVodavi Communications SystemsPage 2 of 22TF NO. 46a
8300 E Raintree Drive
Scottsdale, AZ...

Linfinite 
‘” Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
CO Line Connections:
The 4x8 DID Interface Board has two RJ-14 modular connectors for connecting the CO lines to the system. CO
lines 1 
& 2 are on the J2 connector. Pin 3 is for Ring 1, Pin 4 is for Tip 1; Pin 2 is for Tip 2, Pin 5 is for Ring 2. CO
lines 3 
& 4 are on the J3 connector. Pin 3 is for Ring 1, Pin 4 is for Tip 1; Pin 2 is for Ring 2, Pin 5 is for Tip 2.
Four red 
LEDs are located along the front edge of the 4x8 DID...

infinite ‘” Digital SystemsTF NO: 46a
13
14
15
16Conditions:38
13
39
14
40
15
41
16Black/GreenGreen/Black
BlacWBrown
Brown/Black
Black/Slate
Slate/BlackYellow/Blue
Blue/YellowXmt Tip
Port 07Green
Xmt Ring
Red
Rcve TipBlack
Rcve RingYellow
Xmt Tip
Port 08Green
Xmt Ring
Red
Rcve TipBlack
Rcve RingYellow
.
.
.
.
.
.
.
.
e
.
.
.
.The infinite DVX 
” Digital system supports up to 1000 DID numbers, with a maximum of 200 ring lists to which
DID numbers can point.
4The maximum number of DID trunk circuits...

cinfinite 
‘” Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
A. Direct Inward Dialing (DID) Table Programming:
The buttons on the digital terminal are defined as shown below when entering the DID programming area:
CLEARENTRY
h---l:::::::,:s, 4
1.Press FLASH and dial [44]. The following message is shown on the display phone:
Where:
- RRR= Route Number (000-199)
- ###= DID Number (Directory # from C.O.) (7 digits)
- n..n= Name Assigned to DID Number (8 characters)
To program the Route Number:...

infinite ‘y Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
To program the DID Number:
1.Press the NUMBER Button (Button #2) in the flexible button field for programming the DID Number.
2.Enter the DID Number to be associated with a three-digit Route Number (000-199). Up to 7 digits can be
entered. By default, only the last three digits will be used for routing. This is determined in Flash 45. (Refer 
to
Page 8).
3.The display will show the DID number as it is entered. Press the HOLD button to...

infinite’” Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
To erase a DID Table entry:1.Press the CLEAR ENTRY Button (Button #4) to clear an entire Phone Number, Name and Route from the DID
Table. Press the HOLD button to save the entry. Confirmation tone will be heard and the entry cleared.
To change to a different DID Route:
1.Press the UP Button (Button #18) to advance to the next DID Route number.
OR
2.Press the DOWN Button (Button #19) to go back to a previous DID Route Number.
Default:By...