Trillium Panther Ii Feature Module Iv System Manual

Panther II 820/1032/2064-205 
Not Used on Panther II 1032 System 
. 
TABLE 2-1,7 
FLEXIBLE 
RINGING 
ASSIGNMENT 
Panther II 
1032 System 
Programming 
Page 41  

TrilIium Standard Practice 
TABLE 
2-14 
FLEXIBLE 
RINGING 
ASSIGNMENT 
Panther II 
2064 System 
Use all of Table 
2-13 (for the first 
32 stations), and 
this chart (for the 
remaining 32 
stations) to fill 
in which lines 
will ring at each 
station. 
Programming 
Page 
42  

Panther II 820/1032/2064-205 
GROUP PROGRAMMING 
General by Line 
2.2 0 The 
Group Parameters, including Access Codes and Data Codes are provided in 
Tables 2-15 to 2- 18. The parameters are: 
TENANT GROUP ASSIGNMENT: Up to 8 lines on the Panther 
II 820 system, or 10 lines on the Panther II 1032 system, or 20 lines 
-on the Panther II 2064 system are put into one of 15 Tenant Groups. 
Use Table 2-15 to check off which lines are to be included in each 
group from 01 to 15. Note: A line can be in more...

Trillium Standard Practice 
TABLE 2-15 (a) TENANT GROUP ASSIGNMENT 
-. 
:) ,’ 
TABLE 2-15 (b) TENANT GROUP ASSIGNMENT 
Programming 
Page 44  

Panther II 820/1032/2064-205 
LINE POOLING GROUPS: Up to 8 lines on the Panther II 820 
system, or 10 lines on the Panther II 1032 system, or 20 lines on the 
Panther II 2064 system are put into one of four Pool Groups. 
Use 
Table 2-16 to check off which lines are to be included in each group 
from 01 to 04. 
Note: Only “like” lines should go into a line pool (e.g., a pool is made up of all 
“same area” WATS lines, local lines, FX lines, and so on). The same line will not 
be in more than one line pool...

Trillium Standard Practice 
TABLE 2-16 LINE POOLING GROUPS 
LINES 
POOL 
GROUP 
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 2C 
01 / /’ /’ 
02 
03 
lo41 I I I I I I I ! I I I I I I I I I I I 
Check off each line you would like in each line pool group. 
NIGHT TRANSFER LINE GROUPS: Up to 8 lines on the 
Panther II 820 system, or 10 lines on the Panther II 1032 system, or 20 
lines on the Panther II 2064 system are put into one of four Night 
Transfer Line Groups. Use Table 2-17 to check off...

Panther II 820/1032/2064-205 
Step 5. 
Step 6. 
. 
. 
Press # to store all previous data or dial a new access code. 
Step 7. Press the * key to exit programming when all selections have 
been made. The new programming is complete.  After the inputted data is displayed, press the 
HOLD key to 
store the data and increment to the next line. 
Repeat Steps 4 and 5 until all lines in a particular group are 
programmed, then 
Press the 
HOLD key to increment to the next Night Transfer 
Line Group number, 
OR...

Trillium Standard Practice 
PRIME LINE GROUPS: Up to 8 lines on the Panther II 820 
system, or 10 lines on the Panther II 1032 system, or 20 lines on the 
Panther II 2064 system are put into one of 15 Prime Line Groups. 
Use Table 2- 18 to check off which lines are to be included in each 
group from 01 to 15. Note: A line can be in more than one Prime Line 
group. (Refer also to PRIME LINE PREFERENCE in this 
subsection). 
To enable a PRIME LINE (at individual Sets), refer to 
PROGRAMMABLE KEYS,...

Panther II 820/1032/2064-205 
TABLE 2-18 (a) Prime Line Group Assignment 
General by Station 
2.2 4 The 
Group Parameters, including Access Codes and Data Codes are provided in 
Tables 2-19 and 2-20. The parameters are: 
TENANT GROUPS: (Table 2-19) After the 8 lines on the 
Panther II 820 system, or the 10 lines on the Panther II 1032 system, 
or the 20 lines on the Panther II 2064 system have been assigned to the 
15 Tenant groups (see GROUP PROGRAMMING - General by Line), 
each station must be assigned...

Trillium Standard Practice 
- 
TABLE 2-18 (b) Prime Line Group Assignment 4 :: 
,; 
PICKUP GROUPS: (Table 2-19) In order to perform the Call 
Pickup-Local feature on the Panther II system, each station must be 
assigned to at least one of the ftiteen 2-digit pickup groups (01 to 16). 
The pickup groups should be organized so that stations in close 
physical proximity to each other are placed in the same pickup group. 
Preprogrammed Value = All stations are placed in Pickup Group 01. 
PRIME LINE...