Trillium Panther Ii Feature Module Iv System Manual

Panther II 820/1032/2064-205 
TABLE 2-1 (Cont’d) GENERAL SYSTEM PARAMETERS 
Feature Access 
Description Code Condition 
(Values) Data 
Code 
Call Forwarding 036 5 seconds 
Time 
10 seconds* .Y 
20 seconds  30 seconds 
; 
-___________________~~~~~~--~~~---------~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 
Multiple 0370 sub-attendant of Group 1 
Attendants 0371 sub-attendant of Group 2 E 
0372 sub-attendant of Group 3  0373 sub-attendant of Group 4 
w” 
Default = Station 10 for all...

Trillium Standard Practice 
TABLE 2-l(a) SYSTEM CLEAR 
To perform a System Clear: 
CAUTION: This procedure will RESET all system programming to its 
preprogrammed value, and should therefore be used with extreme discretion. 
System Clear 
Option Selected 
During System 
Programming 
(Access Code 070) To perform, 
dial the 
appropriate 
code from 
Station 10 
(Programming 
Station) Result 
Clear ALL Features 0700# All previous system 
programming will be 
cleared, and the system 
will reset to its...

Panther II 820/1032/2064-205 
C.O. Line Specification Proiramming 
2.0 9 The C.O. 
Specification parameters, including Access Codes and Data Codes are 
provided in Table 2-3. They are: 
MAKE/BREAK RATIO: Defines the on/off ratio of pulses used for 
pulse dialing; either 33% or 40%. 
Note:‘33% is not permitted when equipment is to be installed in North America 
and connected to the North American Telephone Network. 
Preprogrammed Value = 40%. 
PULSE RATE: Defines the speed at which pulse digits are dialed...

Trillium Standard Practice 
TABLE 2-3 C.O. SPECIFICATION PARAMETERS 
Feature Access Condition 
Data 
Description Code (Values) 
Code 
Make/Break 
001 33% 0 
Ri3tiO 40%* 
1 
____________________~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 
Pulse Rate 002 10 pps* 0 
20 
PPS 1 
,,,,,_,,,,,,,,,,,,,,,,,,,,,,,,,-,,,,,,,_~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 
Interdigit 003 800 ms* 0 
Pause 11OOms 
7OOm.s : 
5OOms 3 
Tone 
Duration 004 50 ms 0 
75 ms* 
1OOmS : 
Notes: *...

Panther II 820/1032/2064-205 
TABLE 2-4 TYPE OF LINE PARAMETERS 
Feature Access 
Condition 
Data 
Description Code 
(Values) 
Code 
Tone/Pulse 06Oxx 
Tone* 
0 
Pulse 
1 
__~_________________~~~~~~~~~~~~~~~~--~~~~~~~~~~~~~~~---~-~~~~~~~~~~~~~-~--~~~~~~~~~~~~~~ 
C.O./PBX 061Xx 
Telephone (C.O.)* 0 
PBXKentrex 1 
Notes: * denotes preprogrammed value 
XX = a line number from 01 to 08 on the Panther II 820 system, or 01 to 10 on the Panther II 
1032 system, or 01 to 20 on the Panther II 2064 system. To...

Trillium Standard Practice 
FLASH/CANCEL TIMING: Defines the duration of the Flash or 
Cancel signal. 
Note: Flash Timing is typically 500 msec. while Cancel Timing is typically 1 
second. 
Preprogrammed Value = 1 second. 
.?, 
,’ 
Programming 
Page 
16  

Panther II 820/1032/2064-205 
TABLE 2-5 BEHIND PBXKENTREX PARAMETERS 
Feature 
Description 
Pause on 
Number Access 
Condition 
Data 
Code 
(Values) 
Code 
0120 Pause on 7 - NO* 0 
Pause on 7 - YES 1 
____________~_______~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~_ 
0121 Pause on 8 - NO* 0 
Pause on 8 - YES 1 
____________________~--~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~__ 
0122 Pause on 9 - NO* 0 
Pause on 9 - YES 1 
__________----______~~~~~----------~~~~~~~~~~~~~~~~~~~~~~~~~~_. 
0123 Pause on 0 - NO* 0...

Trillium Standard Practice 
Loud Bell/Relay Control Programming 
2.12 The 
Loud Bell and Relay Control parameters, including Access Codes and Data 
Codes are provided in Table 2-6. They are: 
LOUD BELL OR RELAY CONTROL: Determines whether the 
dry contacts will close to activate a loud bell ringer, or to activate 
optional equipment such as security doors and gates. 
Preprogrammed Value = Loud Bell. 
WARNING FOR DRY CONTACTS: 
DRY CONTACT RATING 
Do not connect ringer loads or AC power directly to 
DC...

Panther II 820/1032/2064-205 
TABLE 2-6 LOUD BELL/RELAY CONTROL PARAMETERS 
Feature Access Condition Data 
Description Code 
(Values) Code 
____________________------------------------------------------------------------- 
Loud Bell/ 018 
Loud Bell* 0 
Relay Control. Relay Control 1 
______^_____________~~~~_~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~-----------~--~ 
Loud Bell Ringing,/ 063Xx 
Rings selected line during 
Ringing Over Raging By Line 
Day Mode* 0 
(DAY MODE)...

Trillium Standard Practice 
Toll Restriction 
2.13 The 
Toll Restriction parameters, including Access Codes and Data Codes are 
provided in Table 2-7. Refer to 
Panther II 820/1032/2064-105, Features and Services 
for more details. They are: 
DIGITS TO DENY: Determines the digit on which dialing will be 
denied for Class B and Class B’ restrictions. Parameter can be from 0 
digits to 15 digits. 
Preprogrammed Value = Denies 8th digit. 
SPLIT RESTRICTION FOR CLASS B: Determines whether 
the first or last...