Toshiba Voice Processing Vp100 Installation And Maintenance Manual

PROCEDURES 7-47 
Action CATNP 100 Description and Response (continued) 
~3 
If a PBX forwarding string is not defined in 
System Parameter 45, the ports are still placed in 
the FWD state but may not have actually been 
. 
forwarded on the PBX. 
6. PS j[ 
7. Verify forwarding 
8. /AltlU 
9. or and t 
10. [Enter] 
11. PowerVP lOOOFF 
12. Wait 15 seconds. 
13. Power VP 100 ON Data transfer begins. 
14. Wait for completion As each step begins and ends. the screen is updated. See 
release note for length of...

7-48 Installation and Main!enance Manual 
Action CAT/VP 100 Description and Response (continued) 
17. Wait for the VP 100 to boot This step takes about three minutes. 
INITJALIZING PORTS.. . DONE. _ 
18. Test Test for normal operation. 
rs If an error message appears during the procedure, refer to Appendix Fe_- Data Transfer 
Mess2~P.s 
------‘-- 
us 
To abort this procedure, press -1 at any time. If aborted, this procedure must be 
restarted and run through to completion before the VP 100 is back in...

PROCEDURES 
7-49 
‘ 7.7 ELECTRONIC FEATURE DELIVERY/REMOVAL - 
The Option Control Chip (OCC) on the Main Board (MB) contains the features contained on the _ 
VP 100. The following optional features can be added or removed from VP 100 systems. 
Software Option Description 
s\v-30004 Networking 
SU‘-20034 
Network Names Confirmati~a 
sU--2004 1 Multilingual Prompts 
s\\--20042 Centrex Integration Software 
’ 
Contact the Toshiba Customer Service department to add or remove VP 100 optional software. 
LEF...

., 
7-50 Installation and Maintenance Manual 
--. 
7.8 SESSION REVIEW AND FILE MAINTENANCE  
.: , 
! 
This section provides information about logging sessions captured during communications with a 
VP 100. Also described are procedures for saving, deleting, viewing, and printing the files 
containing logging information. 
Each time the CAT program is started and enters terminal emulation, a file r-ran& 
CXT.LOG 
captures all the information received from a VP 100. The CAT.LOG file is created by default...

PROCEDURES 
7-51 
_______________________CAT.LOG ope,,& _______--______--_-_- -_________ 
--------------------SYSTEM SOFT??‘ARE RELEASE A.4.3.8 (MhVDD/YY------ 
DAY MM/DD HH:MM:SS Y-Y-YY 100 DEiMO ID:123456 Sfi:123456 PBX:lO OtTgina Information 
(MODEM ENABLED) LAST LOGON: LItiVDD HH:hl&l 
@PASSWORD: 
@U 
____________ _____-_____ SYSTEM CONFfGURaTfGN UPDATE__-_ __-_ __________ 
DAY MM/DD HH:MM:SS YYYY 100 DEMO ID:123456 S/N:123456 PBX:lO 
At the dot (.), enter ? for HELP. 
.A USER 
ADD:710,N,13 
ADD: 
.E...

7-52 Installation and Maintenance Manual 
C:\VMXCAT>DIR SNXXXXXX.lOO\C.AT.* 
Volume in drive C is TEST STA B 
Volume Serial Number is XXXXXX , 
Directory of C:\VMXCAT\SNXXXX~XXIOO 
CAT LO4 43 DD-MM-YY HH:JIMa 
CAT LO1 22037 DD-MM-YY HH:MMp 
CAT LO2 16477 DD-MIM-YY HH:MMa 
CAT LO3 8552 DD-MM-YY HH:lMMa 
t CAT 5 File(s) LOG 30742528 115 12-31-99 bytes free 11:59D 
I 
C:\VM_XCAT>LOG_SAVE XXXXXX I[ 
C:\VMXCAT>ECHO OFF 
This command is used to save a CAT-LOG ftie session 
Saved as LOG file 05 
C:\VMXCAT>...

PROCEDURES 7-53 
n To Stop Session Logging 
The CAT program always starts with session logging turned ON. The folIoa-inp procedures 
explain how to turn session logging OFF. 
_ 
Action Description 
=JT To enter Terminal 
menu. 
Session 
Logging 
Stop Logging I 
Use the A and t keys to highlight. 
Use the A and t keys to highlight. “- 
n To Start Session Logging 
The following procedures explain how to turn session logging ON. 
Action Description 
,a T 
To enter Terminal menu. 
Session Logging 
Use the...

7-54 Installation and Maintenance Manual 
n System Log Directory  
If prior session logs have been saved, multiple log files may be stored within a system’s 
’ subdirectory. Up to 100 session logs can be stored for each system: C_%T.LOG and numbered 
logs from CAT-LO1 to CAT.L99. The procedure to display all logs stored for a given system 
follows: 
1. 
2. 
3. Complete any active communication session with a VP 100 and Exit from the CAT 
program (/Altl E). .‘- 
To print the log directory, turn the...

PROCEDURES 7-55 
., 
_.... 
. 
a$&+ _ . . 
n Saving a Session Log 
The CAT program ala-sys uses the log file name CAT.LOG to store session information. This 
file must exist within a given systems subdirectory before it can be saved. 
To save a session log follow the procedur? below. 
1. 
Complete any active communication session with a VP 100 and exit from the CAT 
program (a E). 
l *- 
2. 
With the DOS prompt C:\VMXCAT> displayed. enter the following command, where 
XXXXXX is the system serial number:...

. . 7-56 Installation and Maintenance Manual 
n Considerations 
The CAT-LOG file is created by default when lo 
gging is enabled. If logging information is . 
saved as individual files, the existing CAT.LOG is renamed to CAT-LXX. The following are 
considerations for managing session log files: 
e To create a CAT.LXX file with a known start time or to create a log file containing only 
desired data, use the following procedure: 
l *- 
1. LOG-SAVE if the information from previous sessions is required. 
*...