Toshiba Voice Processing Vp100 Installation And Maintenance Manual

‘ROCEDURES 7-27 
- _ 
q Restore System Software 
The Restore System Software procedure is used to copy the original \.P I r:*i:i system soft\sare 
from the CAT hard disk 
IO the VP 100. This prccedure should only be us:? t.vhen recommended 
by the manufacturer. . 
The selected system defines which release of System Software will be restored onto the’VP 100 
hard disk. All system software files on the VP 100 are replaced with the original (master) files 
stored in the seiected reiease directory. Any...

7-28 /nsta//ation and Marsnance Manual 
:1. CH 
(1 To clear the Hardware Error table. VP 100 0 prompt 
appears. 
:_‘. Test Test for normal operation. 
. 
c3 If an error message appears durin g the procedure, refer to Appendix B - Dhta Transfer 
Messages. 
CZ 
To abort this procedure, press 
I Escape I at any time. ii aborted, this procedure must be 
restarted and run through to completion before the VP 100 returns to operation. 
- _ 
. 
Toshiba VP Systems Release c I December. 1992  

PROCEDURES 
7-29 
n Restore System Prompts 
The Restore S! stern Prompts procedure is used to copy the original VP 100 system prompts 
from the CAT h2rd disk to the VP 100. This procedure should only be used when recomm;ndsd 
by the manufacrurer. or lvhen a Type. I.6 Hardware Error is logged. as described below. 
_ 
Do not use this Restore System Prompts procedure to add a second set oi 
l~nllaop nrc>mntc Use the Procedure. for Adding a Second Language Prompt 
._..=1_3_ T.__~~T~_. 
Set in this chapter....

7-30 Installation and Maintenance Manual 
q Restore System Promp.ts at Release 5.8 
To restore system prompts for systems at Release 5.8, prepare for a restore as described earlier 
in this section. then follow the steps below, 
To restore system software, prepare for a restore as described earlier in this section. then follow 
the steps below. 
.*- 
Action CAT/VP 100 Description and Response 
1. mFi 
7 
-. A and t 
3. )] 
1. Power VP 100 OFF 
5. Wait 15 seconds 
- 
6. 
Power VP 100 ON 
7. Wait for...

PROCEDURES 
7-31 
c? PO abort this procedure, press (Esfapc at an> time 
To abort this procedure. press [I at an>- rime. Ii aborted. this procedure 
must be restaned and run through’ 
to coinpletion before the VP 100 returns to 
operation. 
. 
. 
Toshiba VP Systems Release 6.1. December. 1992  

.. 
7-32 Installation and Mairznance Manual 
n Restore System Prompts Sets Beginning with Release 6.1 
To restore system prompts for systems at Release 6.1 or later, prepare for a Restore as 
t=scribed earlier in this section. then follovy the steps below. 
~ 
Action CAT/VP 100 Description and Response 
: IEnrrr) 
_. 
’ -_ Power VP 100 OFF 
5. Wait 15 seconds This delay is for the VP 100 hard disk drive to spin down. 
Please power ON the system. 
5. Power VP 100 OS 
-_ Wait for completion Data transfer...

PROCEDURES 
7-33 
_, 
*** 
LW To abort this procedure, press -1 at any time. 
b WARNING 4 
If 
aborted. this procedure must be restarted and run through to completion 
before the VP 100 returns to operation. 
? 
Toshiba VP Svslem?. Release 6.1 December. 1992  

lnstallatidn and Maintenance Manual 0. 
7-34 
7.4 HARD DISK DRIVE REPLACEMENi- PROCEDURE 
This section describes the procedure to replace a VP 100 hard disk. Information is provided to 
prepare for a hard disk drive replacement and to replace the hard disk drive. 
, 
The circumstances under which the VP 100 hard disk must be replaced are: 
.‘- 
. 
When a Type 2 Root ROM diagnostic error occ?lrs. 
l When Hardware Error types 17 or 18 are logged. 
0 
When Hardware Error type 16 continues to be lo 
gged...

PROCEDURES 
7-35 
The Restore System Disk menu option is only available when a system is selected. All data to be 
r,-stored is copied from subdirectories on the CAT hard disk to the VP 100. The subdirectories used 
during this restore procedure are determined by the selected system’s serial number, release of 
system software. and by the release of prompts defined for the system. Refer to CONFIGIJRATION 
.\PPLIC.\TIONS TERMINAL, Software Description in this manual. 
.
y GNSSM that had previously been...

7-36 Installation and Maintenance Manual _. - . . 
Replacement Procedure 
The following equipment is needed for this procedure and should be assembled prior tc 
starting: 
0 
A replacement VP 100 hard disk drive. 
uz 
ONLY TOSHIBA SUPPLIED HARD DISK DRIVES CAN BE USED WITH 
THE VP 
100. l *- 
0 
A fully operational CAT with all VP 100 PC software installed (refer to the .CAT chapter). 
0 
A CAT interface cable. 
0 
The configuration diskettes for the customer location (unless the backed up configuration...