Toshiba Voice Processing Vp100 Installation And Maintenance Manual

PROCEDURES 7A-1 
APPENDIX A 
PROCEDURES 
SYSTEM SERIAL NUMBER SUBDIRECTORIES -‘. 
l 
This is a sample listing of all system serial number subdirectories displayed when the following 
command is issued at the C:\VMXCAT> prompt: 
C:\VMXCAT>dir sn* 
Volume in drive C has no label 
Directory of C:\VMXCAT 
SNOOO002 100 (DIR> MM-DD-YY 
SNOOOOll 100 (DIR> MM-DD-YY 
SNOOOOOS 100  MM-DD-YY 
SNOO0019 100  MM-DD-YY 
SNOW320 100  MM-DD-YY 
SNOOOO24 100 &DIR> MM-DD-YY 
SNOOO023 
’ 100  MM-DD-YY 
SNO00006 100...

. . PROCEDURES 78-l 
APPENDIX B 
PROCEDURES 
DATA TRANSFER MESSAGES 
The CAT displays one screen to indicate when data transfer is complete, and another screen to 
indicate that a data transfer error has occurred. The format of the information within each screen is 
always the same; the actual information reported varies. 
In the following examples, the bold type indicates information that does not change. A list of the 
possibIe text entries that can appear within the parentheses is listed at the end of...

7B-2 Installation and Maintenance Manual ‘I 
n Possible Screen Entries 
The following are the entries n-hich can be displayed on the screen. 
Procedure Names: 
Backup Greetings/Names/Script 8r Sequential Messages 
Backup System Configuration 
Restore Greetings&am&Script 5.1 Sequctitiai Messages 
Restore System.Configuration 
Restore System Prompts 
Restore System Software 
Restore System Disk 
Update 
Step of Procedure: 
Displays the actual step of the procedure being performed when the error occurred....

STANDARD DTMF lNTEGRAT_lON 
Chapter Contents 
Section Description Page 
8.1 
8.2 
8.3 Stnnrhrrl DTMF integration vs. Adaptive Integration. 
__-..--. - - ....................................................................... 8-l 
Message Waiiing Indication (MWI). ............................................................................................ 8-l 
Called ?arty Identification (CPI) ................................................................................................. 8-1 
Standard...

INTRODUCTION 
This chapter contains information about standard phone system integration with the VP 100. 
Topics discussed include: 
. 
Stand&d DTMF Inte_qtion vs. Adaptive Integration. 
. 
Standard DTMF Inte_qtion. 
0 
Message Waiting Indication. 
. 
Called Party Identification. 
. 
VP IOOLPBX Interaction. 
Toshiba VP Systems Release 6.1 December. 1992  

STANDARD DTMF INTEGRATION 
8-l 
8.1 STANDARD DTMF INTEGRATION VS. ADAPTIVE INTEGRATION 
-- 
Standard DTMF Integration and Adaptive Integration (AI) depend on the capabilities of a PBX and 
standard or optional features of the VP 100. 
Standard DTMF Integration and Adapti\-e Integration use VP 100 standard features. However, Adaptive 
Integration enhances the operation beyond standard DTMF integration, dependent upon PBXKO 
capabilities and therefore may require additional hardware, consisting of modems...

8-2 Installation and Maintenance Manual 
STANDARD DTMF INTEGRATION 
The standard connection between the VP 100 and PBX phone system is a 2500-type single line kxtension. 
VP 100 Line Interface Cards (LLIC) accept a series of PBX single lines. By emulating the touchtone 
. 
telephone sets the PBX is expecting, rhe VP 100 performs all the operations that are normall>- possible 
from a single-line phone - receiving calls, taking messages, transferring calls, and initiating PBX 
functions by dialing DTMF...

8.3 VP lOO/PBX INTERACTION IN STANDARD DTMF INTEGRATION 
 
; 
This section explains how the phone system and the VP 100 interact when switching calls from the VP 100 
port to a called sration in standard DTMF integrated environments. 
n Primary and Secondary Answering 
Figure S- 1 illustrates the interaction between the VP 100 and the PBX in a standard DTMF integration 
inslaiiation_ where both Prilrl~--y alld Seco,ida,-y Aiiswei-iii - .-- ^ ~ - ^ --- ..-- J ,..-...I..- ..c 
Figure S-l follows the...

8-4 Insfaallation and Maintenance Manual 
q Secondary Answering Only 
Figure 8-2 illustrates the interaction between the VP 100 and the PBX in a standard DThIF integation 
installation, where only Secondary Answering mode is used. An explanation ofFiGme 8-Z follows the 
. 
diagram. 
l-N&S 
=578-3346= 
PBX 
.-_ -- 
0 1 
1- 
Station 
Lines 
345,.- I 
316 
(Forwarded to 
2500 on Busp 
or _Yo _bslfer) 
20 .n 1 VP100 
Figure 8-2 VP 1 OO/PBX Interaction - 
Standard DTMF integration, Secondary Answering Only...

. . 
ADAPTIVE INTEGRATION 
Chapter Contents 
Section 
9.1 
9.2 
9.3 Description Page 
Adaptive Integration .......................................................................................................................... 9-l 
Types of Adaptive Integration ........................................................................................................... 9-3 
Enhanced DTMF In-band Integration.. ....................................................................................... 
9-3...