Toshiba Voice Processing Vp100 Installation And Maintenance Manual

PROCEDURES 7-37 
Action CATNP 100 Description and Response (continued) 
6. 
TEC 1 b=- 
7.PS I 
8. 
9. 
10. 
11. 
12. 
13. 
Verify- forwarding Pisce a test call to the VP 100 and verify the ports have 
b-en forwarded and that the call is anslvered by a live 
ir.iercept. 
Backup system xniigurarion q-e Backup 
- System Configuration section in this 
i%pter. 
Backup GNSS\l 
Power VP 100 OFF 2nd 
replace rhe VP 100 hsrd 
disk drive 
=\lrlT q-2 Backup - GNSSM section in this chapter. 
_.L 
F;lllo\v the...

7-38 installation and Maintenance Manual ., 
Action CAT/VP 100 Description and Response (continued) 
14. r 
To change baud rate. The Baud Rates menu appears. 
15. * and - Move to 38400. Selection is highlighted. 
16. m To accept new baud rate. Status line displays b&d rate 
of 38400. 
18. or and t Move to 
System Disk. Selection is highlighted. 
19. D=-l 
20. Power VP 100 ON The data transfer procedure begins immediately after the 
power is applied. 
For VP 100 systems at Release 5.x, go to step 30 and...

PROCEDURES 7-39 
Action 
_ 
CAT/VP 100 Description and Response (continued) 
25. A 
and t 
26. b=-l 
27. [ 
28. IEnter 
29. (Enter 
30. 
Wait for completion 
31. [ 
32. [ -1 
33. Wait for the VP 100 to boot 
34. 
1 Enter 1 
35. Logon 
36. Test Test for normal operation.  Move to the language prompt set number for the 
language being installed. Select 
none if the VP. 100 does 
not have the Multilingual Prompts feature. 
_ 
Selection is highlighted. 
If none is selected, Prompt Set 1 is loaded ontb the...

7-40 Installation and Maintenance Manual I. ._ _ 
7.5 
. 
HARD DISK DRIVE UPGRADE PROCEDURE : 
This section describes the procedure to upgrade a VP 100 hard disk to a higher capacity hard disk 
drive. A hard disk drive upgrade provides additional hours of voice message storage. Information 
provided is preparation for hard disk drive replacement and hard disk drive replacement procedures. 
Refer to the Disk Usage report to determine when to install a higher capacity drivti: Refer to the 
REPORTS chapter...

PROCEDURES 
7-41 
n Upgrade Procedure 
The following equipment is needed for this procedure and should be assembled prior to 
starting: 
0 
The new 1-P 100 hard disk drive. 
- >. u?c? ONLY TOSHIBA SUPPLIED HARD DISK DRIVES CAN BE USED WITH THE 
VP 1nn 
. I A”“. 
.‘- 
0 A fully operational CAT with all VP 100 PC software installed. Refer to the. CAT chapter. 
0 
A CAT interface cable. 
To replace the VP 100 hard disk. perform the following steps. 
Action 
CAT/VP 100 Description and Response 
1. Start the...

7-42 Installation and Maintenance Manual .,. 
Action CAT/VP 100 Description and Response (continued) 
! 
7. PS II 
8. Verify forwarding 
9. Backup system configuration 
10. 
11. 
12. 
13. A and t 
14. [ Enter 1 
15. 4 and t 
16. 1 Entsr 1 
To display the Restore menu. 
18. * and t Move 
to System Disk. Selection is highlighted. 
19. 
20. 
Power VP 100 ON The data transfer procedure begins immediately after the 
po\ver is applied. Data transfer begins. 
/  Backup GNSSM 
Power VP 100 OFF and 
replace the...

PROCEDURES 
7-43 
Action CAT/VP 100 Description and Response (continued) 
For VP 100 systems at Release 5.x, go to step 30 and 
follow the steps from 30. 
21. [ 
22. * 
and t 
23. /Enrzr] 
24. -1 
25. 1 and - 
27. :J 
For VP 100 systems at Release 6.1, continue with step 
21. 
A ***WARNING*** screen appears asking’rhat Release 6 
Prompt Set(s) be selected from the menus that follow. 
Choose new Prompt Set screen appears showing the 
first language as 
Prompt Set 1. 
Move the the language prompt set...

7-44 InstaXation and Maintenance Manual I. . . 
Action CAT/VP 100 Description and Response (continued) 
28. [Enter1 
29. [Enter 
30. 
Wait for completion 
31. I 
32. (1 
( Enter ] 
33. Wait for the VP 100 to boot 
34. I 
35. Logon 
36. Test If Prompt Set 2 is United States English, a 
. 
“‘WARNING*” screen appears stating that U.S. English . 
has been selected for Prompt Set 2. For all other 
languages installed. the screen states that U.S. English 
u-as not selected. 
Both prompt sets 
are loaded onto...

PROCEDURES 7-45 
7.6 -  SYSTEM SOFTWARE UPDATE PROCEDURE 
The following is nn es:ic~plr of thf Update I~C~LI. 
To Release A.04.XX.XX 
To Release A.04.XX.XX 
Update disk on the VP 100 to Release A.05.02.02  

. . 
7-46 Installation and Maintenance Manual 
‘> lz= The Update procedure must be done onsite with a cabled connection to the VP 100 at 38400 
baud. and requires the VP 100 to be out of service for the duration of the procedure. 
Sew VP 100 software releases from the manufacturer are generally accompanied by a software 
release notice describing rhe changes, improvements, and modifications to the VP 100. The notice 
may also contain specific instructions for installin, 
0 the new release on the CAT haid...