Toshiba Voice Processing Vp100 Installation And Maintenance Manual

PROCEDURES 7-17 
- _ 
F~liow the instructions displayed on the screen. The first example screen is irEm a Zenith 
lrptop. The second example screen is from a Toshiba TI 600 laptop. 
. 
C:\\>lSCAT> SYS_B.%CK 000002 
The command is used to backup a CAT system to 
flbppy diskette(s) 
BACKUP version 3.30.06 
Copyright (C) 1988 Zenith Data Systems Corporation 
Insert first backup disk in drive A: 
Format back-p disk (Y/N) ? Y 
Format low or high density (LM) ? H 
FOFMAT version 3.30.05 
Copyright (C) 1988,...

7-18 Installation and Maintenance Manual 
RESTORE PROCEDURES 
7.3 
This section describes how to restore information to a VP 100. The Restore procedure transfers 
information from the CAT hard disk drive to the VP 100. To restore system configuration and 
GNSSM information to the VP 100, it must have been previously backed up to the CAT hard’disk 
(by using the Backup procedures) and archi\-ed to floppy diskette. 
l *- 
Information in this section describes the foiiowipg: 
l Recover VP 100 from floppy...

PROCEDURES 
7-19 
The following is an example of the Restore menu. Beginnin, 
0 with Release 6.1. the window lists 
System Prompts (Set-l) and System Prompts (Set-2) as sho\
. The screen may display different 
worciinz if the Toshiba VP System software is at another release. 
System Configuration (PRELOAD) 
System Software Release A.&.xx.xx 
System Prompts (SET-l) 
’ 
System Prompts (SET-2) 
System Disk 
Restore 
Greetings. 
Names and/or Script & Seq 
Msgs from the PC to the VMX 
100 
. 
. 
Toshiba VP...

7-20 Installation and hlaintenance Manual . . 
n Recover VP 100 System from Floppy Diskette 
All information for each VP 100 system previousl!. archived to floppy diskette can be 
recovered or copied back to the CAT hard disk by using the procedure described below. 
Systems should be recovered priorto a Re’store procedure. usually prior to replacing a failed 
VP 100 hard disk drive. 
Information recovered for each system is exactly what had been previously arc&ived, including 
the system configuration....

PROCEDURES 7-21 
n Restore Preparation 
The following esplains ho
 to prep:xc for the VP 100 Restore procedure. 
Action CAT/VP 100 Description and Response 
- _ 
1. Start the CAT program Select System screen is displayed. Refer to the CAT 
chapter. 
2. Select system to restore Tsrminai emuiarion begins. Refer to ihe&eiect System 
Scrs:n section in this chapter. 
Check the status line of the CAT screen and verify that 
the proper system serial number has been selected. If the 
system to be restored is not...

-. 
7-22 installation and Maintenance Manual .. 
8. Verify forwarding 
Place a test call to the VP 100 and verify the ports have 
been forwarded and that the call is ans\versd by a Ii\-e 
intercept. 
. 
Refer IO the specific Restore procedure in this chapter for further instrwrions 
Toshiba VP Systems Rdeze 6.1 December. 1992  

PHOCEDURES 
7-23 
n Restore System Configuration (Preload) 
“i 
Once a system configuration database has been backed up from the VP 100 to the CAT hard 
disk. the database can then be restored (copied) from the C.\T hard disk to any VP 100. This 
procedure can be used to restore an original configuration to a system. For example, on a 
system where numerous changes were’made’that are no longer desired or are incorrect. 
The Restore System Configuration procedure can also be used to place a “templafe”...

7-24 lnstalation and Maintenance Manual 
- _ 
n Restore - Greetings, Names, Scripted, & Sequential Messages 
(GNSSM) 
This procedure is used to restore Greetings. Names. Scripted. and Sequtntial Messa~rs 
(GNSSM) from the CAT hard disk to the VP 100. For example. to restpi? original GNSS\l to a 
system that had a hard disk drive replaced or upgraded to a larger capsciiy drive. 
, 
E? 
To restore information to the VP 100. it must have been previously backed up (saved) on 
the CAT hard disk by using the...

PROCEDURES 7-23 
Prepare for a restor: 3s deixibetl in the Restore Preparation section, then iollo;v ths steps 
below. 
cz= Verify that ths baud rate is 19100. 
Action CAT/VP 100 Description and Response 
I. gi3 With the @ prompt displayed, obtain the Restore Menu. 
4. Enter information into 
GNSSM Restore menu Refer below to the description of each field. 
5. [Enter1 Once rhe destination mailbox is enrered, the procedure 
begins immediately. The 
GNSSM Restore menu 
disappears and data transfer begins....

7-26 installation and Maintenance Manual 
Action CAT/VP 100 Description and Response 
1. 4 and t- 
Move to original mailbox field. 
Field entry is highlighted. 
. 
’ B 
_. 
To display a list of all GNSSM backed up on the CAT 
hard disk for the selected system. List appears. 
3. Scroll through list. Use the arrow keys to select the desired ‘Failbox (or 
ALL). Selected item is highlighted. 
That mailbox number is placed in the 
Original Mailbox 
field, and the cursor advances to the 
Destination 
Mailbox...