Toshiba Voice Processing Vp100 Installation And Maintenance Manual

6-48 
Installation and Maintenance Manual 
Hard Disk Main Board 
I 
Power 
/ SUPPlY 
Figure 6-7 
The VP 100 Cable Connections 
VP Systems Release 6.1 kcember. 1992  

“1 ..“I 
MAINTENANCE 6-49 
n Line Interface Card (LIC) Replacement 
_- .- 
If a LIC problem occurs, the card must be returned to Toshiba for replacement. Components on 
the LIC are not replaceable. 
- 
b 
WARNING 4 
The VP 100 must be turned OFF before inserting or removing a LIC. 
l .- 
The procedures to remove and add a LIC are below. Be careful not to touch the components on 
the LIC. Handle the card carefully, touching it only on the sides and using the extractors. Use a 
wrist grounding strap to...

’ 6-50 Installation and hfahtenance Manual 
6: When the VP 100 comes up, logon by entering the passlvord. 
7. Verify that the additional ports exist. At the @ prompt, enzr: PS. 
, ‘) 
_ 
8. Test the rrew LIC. At the @ prompt, enter: TE L 1. 
9. Test the new ports for call processing and message taking 
capabilities. 
.‘- 
10. Add the new extensions fo the existing PBX hunt group. 
Hard Disk Drive (HD) Replacement 
Hard disk drives are initially shipped installed in the cabinet. When a replacement is...

MAINTENANCE 
6-51 
- _ 
. 
In the event of damage or malfunction, the PS may require 
replacement. The following describes how to remove the PS safely. 
1. Remove the outer cover to gain access to the inner components. 
Be sure to turn OFF the input power before opening the metal 
case. 
2. Remove the input power cord. 
3. Loosen the PS retaining screws and remove the power supply. 
This allows easy access to the DC power cables. - 
4. Disconnect the disk power cables at the power supply. There are...

6-52 installation and Mainrenance Manual 
installing Power To install the PS safeI>,. perform the steps in the following order: 
f‘ 
SUPPlY 
I. Make sure the input po\ver switch on the PS is turned OFF. 
3 
_. 
4. 
5. 
6. 
Place the PS into the VP 100 cabinet. 
Reconnect the three DC power cables to the MB, the HD, and the 
fan. 
Tighten the four PS retaining screws. 
Connect the input pouer cord. 
Close the metal and plastic cases. 
n Fan Replacement 
Removing Fan 1. 
When the system is up. check for...

MAINTENANCE 
6-53 
- _ 
.r ‘4 
. 
n Option Control Chip (OCC) Replacement 
Th? OCC is the component that contains the features that each VP 100 is equipped with. The 
OCC assembly is an S-pin integrated circuit that is inserted into a socket soldered onto the 
Llain Board. 
. 
Ths OCC must always remain with the system it was purchased for. If a Main Board is being 
replaced. the OCC must be removed from its socket and placed into the socket on the Main 
Board of the replacement cabinet. It is...

6-54 installation and Mhtenance Manual 
6.10 VP 100 COMPONENT DESCRIPTIONS AND PART NUMBEds 
Component 
Metal case with Main Board and cable 
Cable - CAT Interface 
Cable - Terminal Interface 
Fan 
Part Number 
2OO-0147.-00 1 
5 10-0326-00 1 
l *- 
5 10;0327-001 
200-0156-001 
-. - _ 
. 
Hard Disk - 2.5 hour 
Hard Disk - 6.0 hour 
Hard Disk - 11 .O hour 
Line Card 
Option Control Chip 
Power Supply 
. . 
1 OOHD-2.5 
lOOHD-6 -. _ 
1 OOHD- 11 
VP-2P 
152-0709-00 1 
200-0144-011 
Toshiba VP Systems Release...

7 
PROCEDURES . 
Section 
?.t 
7.2 
_. 7.4 . 
7.5 
7.6 
7.7 
7.8 
7.9 
i’ .. j 7.10 
Appendix A 
Appendix B 
Chapter Contents 
Description 
Page 
_. 
CAT Menu Options 
........................................................................................................................... 1-1 
Select System Screen ................................................................................................................ 7-2 
Help Menu....

_ 
INTRODUCTION 
. 
This chapter explains the VP 100 procedures available through use of the Configuration Applications 
Terminal, referred to as the CAT. The VP CAT menu option scrcsns and the VP 100 procedures are 
described. CAT hard disk drive procedures are also described. 
The CAT is used to initiate the prcxedures described in this chapter. The CAT is an IBM c‘gmpatible PC 
with a floppy drive and an internal hard disk drive. 
l The CAT floppy drive is used to transfer programs and files to and...

This chapter contains the following information. 
CAT Menus 
Backup Procedures 
Restore Procedures 
- _ 
VP 100 Hard Disk 
Replacement 
VP 100 Hard Disk 
Upgrade 
VP 100 System 
Software Update 
. 
Session Review 
CAT Hard Disk 
This section explains the procedures to remove a VP*100 system from the CAT 
Drive Operations hard disk drive, and provides guidelines for CAT hard disk drive maintenance. 
Appendix A 
Appendix B 
This section explains the Select System screen options and the Help, Exit, and...