Toshiba Estudio 170f Manual

109
This function is for utilizing
various information services
via the telephone.
Even when the dial type of your
facsimile is set to DP (Dial
Pulse) type, the facsimile can
generate a TONE signal to ac-
cess information services such
as facsimile-on-demand sys-
tems, voice menus, etc.
Once on line, generating the
TONE signal can be accom-
plished by pressing:NOTE:
From the moment when
 is pressed until the end
of that transaction or until
you press 
 again, touch-
tone (MF) signals will be
transmitted...

110 - COMMUNICATION STATUS
In the Standby Mode, press:
JOB STATUS
The following screen shows an
example of the Job Status dis-
play when the phone line is in
use for 10 seconds (BUSY
lamp blinking):
With the phone line status in
Step 1 displayed, you can ei-
ther continue or cancel the job.
To continue, wait for the fac-
simile to return to the Standby
Mode or press 
STOP
.
To cancel and erase the dis-
played job, press:
JOB CANCEL
Press one of the following
keys.
To cancel the job, press:To continue...

111
A screen such as the one be-
low is displayed while a docu-
ment is being transmitted in
the Direct Transmission Mode.
Press:
STOP
Select the desired option.
To cancel the transmission,
press:After the document exits, the
menu returns to the Standby
Mode.
To continue the transmission,
press:
Reserved jobs can be can-
celled while they remain in
memory. The following 5 types
of jobs can be cancelled using
this procedure.
1. TRANSMIT
2. RECEIVE
3. POLLING
4. POLLING RESERVE
5. JOB NUMBER
In the Standby...

112Select the desired job type.The operation and screen to
follow varies for each item
number selected.
If you selected 2.RECEIVE, go
to Step 3.
If you selected 5.JOB NUM-
BER, go to Step 3.
If you selected:
1. TRANSMIT
3. POLLING
4. POLLING RESERVE
Go to Step 4.
Enter the job number you want
to cancel.
Display the status of the de-
sired job by using 
MENU
and/or 
.
Go to Step 5.When the desired job screen is
displayed, press:
 
A screen like the one below is
displayed.
Select the Job Type
2
Enter JOB...

113
The Group Broadcast Trans-
mission feature allows you to
send a document to multiple
remote parties in a single oper-
ation.
Note that a Group Broadcast
Transmission requires all pag-
es to be scanned to memory
prior to dialing, and thus ade-
quate residual memory is re-
quired.
NOTES:
• If the optional handset is
installed, handset dialing
is not available.
• Up to 50 groups can be
assigned.
• To confirm the Group
Number Registration,
see the Group Number
List.  (See page 204.)Load the document face...

114The Multi-Key Quick Broadcast
Transmission allows docu-
ments to be sent to a combina-
tion of the following numbers
without pre-programming a
group.
• One Touch Dial Keys
(See page 90)
• Abbreviated Dial Numbers
(See page 91)
• Alphabet Dialed Numbers
(See page 92)
• Keypad Dialed Numbers
(See page 93)
NOTE:
Up to 288 destinations can
be assigned in total using
the Keypad Dialed Num-
bers, One Touch Dial keys
and Alphabet Dialed Num-
bers. However, up to 100
destinations can be as-
signed using only...

115
You can cancel or retain the
Manual Group Dial Number reg-
istered in this facsimile.
Press the One Touch Key or
Abbreviated Dial Number you
want to delete, and press:
Multi-Key Quick Broadcast Transmission - continued
Cancel the Existing
Number
4a
Retain the Existing
Number
4b
Press:
START
Press the START
Key
5
Select the CANCEL or RETAIN Facsimile Number
4
Standby Mode screen
When document
scanning is completed:
2.RETAINALREADY ASSIGNED
1.CANCEL
ABB NBR=         154
ARE YOU SURE ?ABB NBR=...

116
What is a “Relay Transmission”?A relay transmission is used to send documents from your facsimile (origina-
tor) to a Hub Station, which then sends them to additional end stations. If you
have several stations in one or more regional areas (e.g. Los Angeles Metro,
New York City, Dallas-Ft. Worth, Seattle-Tacoma, etc.); you can save time
and phone charges by setting up a relay system. By sending your document
to a Hub Station, you can then instruct the Hub Station to retransmit the docu-
ment to the...

117
Press:
MENU++
This section describes the pro-
cedures to send a document to
Relay Box in a relay station.
The relay station must be com-
pliant with ITU-T F-code com-
munications. For more informa-
tion, see page 116.
NOTE:
The destination relay box
must be setup in the remote
hub unit prior to sending
documents.Load the document face down
in the Document Support (see
page 83).
Adjust the resolution and con-
trast if desired (see pages 84
and 85).Press:
+
Relay Transmission Originating Procedure
Load...

118
Relay Transmission Originating Procedure - continued
Enter the password to access
the Relay Box.Then press:
Enter the facsimile number of
the remote hub unit using any
of the following dialing meth-
ods.
• One Touch Key Dialing
... See page 90
• Abbreviated Dialing
... See page 91
• Alphabet Dialing
... See page 92
• Keypad Dialing
... See page 93The facsimile starts scanning
the document into memory.
The following screen is dis-
played for about 2 seconds be-
fore returning to the Standby
Mode....