Toshiba Dp5018ds Instruction Manual

Background Music
You can set background music over your telephone speaker or over external speak-
ers. At least one music source must be connected to your system. Up to 16 different 
music sources can be applied to the Strata CIX/CTX system: the first source is Quiet 
Tone, all others can be music or recorded information.
‰	 To	 enable	 background	 music	on	your 	telephone	 speaker
‰  Press 
BGM. LED turns on.
Or press an extension button + 
#490 +  n + #, where  n is the music source 1~15. 
‰	 To...

Strata CIX DP5000-series Telephone UG     01/08
1. While on a call, press Park in Orbit or press           (Cnf/Trn) + #33. The 
LED flashes green (consultation-hold). If you were on an extension during the 
call, and you have line button on your telephone, the line LED will flash until the 
call is picked up (depending on programming).
2.  Specify the Park Orbit using one of the following:
•	 Press	
* and the system automatically selects a General Park Orbit between 
7000~7019. The chosen orbit appears...

Call Forward
There are two types of Call Forwarding that you can set. One is System Call 
Forward (set in System Programming) which automatically directs calls to a pre-
defined location, such as Voice Mail. See your System Administrator to determine or 
change your System Call Forward destination. 
The other type is Station Call Forwarding. You can use Station Call Forwarding to 
replace your System Call Forward destination with a custom Call Forward setting 
made from your station.
System
System Call...

Station Call Forward Categories
You can set Call Forward for the following categories of calls. Within these catego-
ries, you can use five different types of Call Forward Settings (as detailed in the next 
section).
•	 Call	Forward	 Any	Call – Forwards any call, whether an internal call or incom-
ing line call.
•	 Call	 Forward	 -	Incoming	 Line – Forward incoming line calls only. 
•	 Call	 Forward	 Any	Call	-	Set	 for	Another 	Station – Enables you set forwarding 
of all calls for another telephone...

•	 Call	Forward	 Cancel – Cancels the set Call Forward feature. Notice that each 
category of Call Forward has a different code for canceling.
Station Call Forward Procedures
Table 15 on Page 105 contains Call Forward Button sequences. You can do a Call 
Forward function by entering the button sequence as described or by programming a 
Programmable Feature Button to perform the sequence. See  “Programming Feature 
Buttons” on page 84 to program a Programmable Feature Button.
‰  To use the Call Forward...

Sequence” heading. Some features require additional input, such as:
•	 Dest.	Ext.	or	Telephone	 No. – Call Forward destination numbers can be 
internal extension numbers or outside telephone numbers. If the destination is 
an outside number, enter the access code used for dialing out (such as 
9) + the 
telephone number + 
#. The CIX accepts destination numbers of up to 32 dig-
its.
•	 Timer – Enter the number of seconds (08~60) your telephone should ring  before forwarding the call. (This is the Call...

Call Forward Examples
‰	 To	set	your 	telephone	 to	Call	 Forward	 Busy-No	Answer	to	 an	 internal	 extension	
number
‰  Press your extension button + 
#6041 + 3000# + 10
#6041 = Call Forward Access Code sequence 
3000# = Internal Extension Number 
10 = Ring time in seconds before Call Forwards
‰	 To	 set	another 	telephone	 to	Call	 Forward	 Busy-No	Answer	to	 an	 outside	 desti-
nation	 number 	after 	a	 set	 time
‰  Press your extension button + 
#6042 + 1234 + 1111 + # + 9 +1 949 
5873000
 + # + 08...

Call Park Orbits
The Call Park feature enables you to hold a call temporarily in a location other than 
your telephone. These areas are called orbits. You or another telephone user can 
retrieve a parked call from its orbit by specifying the orbit number. You can specify 
one of 20 General Park Orbits (7000~7019) or a valid extension number within the 
system.
Once you have parked a call in an orbit, you can:
•	 Hang	up	and	 retrieve	 the	parked	 call	at	a	later	 time
•	 Originate	 another	call
•	 Access...

‰ To retrieve a parked call
1. Press 
Park in Orbit or press your extension button + #32.
2.  Enter the Orbit Number where the call is parked or 
# for the extension from 
which you are calling. You cannot use 
* to retrieve a parked call. The extension 
LED flashes at the in-use rate when the call is retrieved.
Call Pickup
You can pick up a call that is ringing another station’s extension, a call placed on 
hold at another station and other types of calls. When you pick up an internal call, 
the calling...

‰ To perform Call Pickup
‰ Press the buttons shown in the table below for the desired Pickup feature.
•	 The	 Primary	 extension	 number	is	the	 directory	 number	by	which	 the	telephone	
set is defined. Other, non-primary extension numbers may also appear on the 
telephone. By convention, the Primary extension number is assigned to the first 
button (on 
the bottom left-hand side) of a multi-button telephone.
•	 If	 more	 than	one	call	is	on	 hold,	 the	call	 on	the	 telephone’s	 lowest	button	number...