Timex Sun and Moon User Manual

							TO USE CHRONOGRAPH FOR LAP OR SPLIT
TIME MEASUREMENT:
1)   PRESS pusher “A” to bring up CHRONOGRAPH display; “CH LAP” or “CH SPL” will appear.
2)   PRESS pusher “D” to select LAP or SPLIT.
3)   PRESS pusher “C” to start timing.
4)   PRESS pusher “C” to record the first Lap or Split time; digits will be frozen for 15 seconds; “L” or
“S” will flash to indicate that the next Lap or Split
time is being recorded in the background.
5)   PRESS pusher “A” to view the running display while the display is frozen.
6)   PRESS pusher “C” to take another Lap or Split.
7)   PRESS pusher “D” to stop.
8)   PRESS pusher “D” again to reset.
NOTE: CHRONOGRAPH must be reset to zero to
switch between LAP and SPLIT.
Records time up to 24 hours and shows 1\f100 of 
seconds for the first hour.
15
E N G L I S H
NOTE:
When the timer counts down to zero it will beep for
20 seconds.
To stop the timer beep, PRESS any pusher.
“T” will appear to designate that the countdown
timer is running.
Countdown time up to 24 hours.
PRESS and HOLD pusher “C” for 2 seconds in setting
mode, to activate fast advance.
TO USE CHRONOGRAPH FOR STANDARD 
MEASUREMENT:
1)   PRESS pusher “A” to bring up CHRONOGRAPH dis play; “CH LAP” or “CH SPL” will appear.
2)   PRESS pusher “C” to start timing.
3)   PRESS pusher “D” to stop timing.
4)   PRESS pusher “D” to reset.
1\b
E N G L I S H
OR 
						

							NOTE:
1)   While in setting of any mode, if no pusher ispressed for 90 seconds the display will automati
cally return to TIME \f CALENDAR mode.
2)   While in any mode other than TIME \f CALENDAR mode, whenever pusher “C” or “D” is pressed, the
next press of pusher “A” will automatically return
the display to TIME \f CALENDAR mode.
17
E N G L I S H
TO SET DUAL TIME:1)   PRESS pusher “A” to bring up DUAL TIME 
display. “T2” will appear
beside the dual time.
2)   PRESS and HOLD pusher “D”; “Hold” will display until hour flashes.
3)   PRESS pusher “C” to advance hour.
4)   PRESS pusher “A” to let month flash.
5)   PRESS pusher “C” to advance month.
6)   PRESS pusher “A” and “C” as above to adjust date, day, and to set 12 \f 24 hour format.
7)   PRESS pusher “D” to complete setting.
     NOTE:
     PRESS and hold pusher “C” for 2 seconds in set ting mode to activate fast advance. 
16
E N G L I S H
HOUR MINUTE 
						

							TO SET THE TIME1)   Pull crown all the way out and turn to correcttime. 
2)   Push crown in to restart. 
Note:  24hour display will set automatically.
TO SET THE DATEInstant date change: 
1)   Pull crown out one stop and turn CLOCKWISE 
(if not, COUNTERCLOCKWISE) until you reach 
correct date. 
2)   Push crown in to restart.
19
E N G L I S H
MULTIFUNCTION MODELS
Your watch has a normal large face display and three
small faces displaying date, day and 24hour time.
TO SET THE DAY1)   Pull crown all the way out and turn CLOCKWISE until correct day appears. 
2)   Push crown in to restart.
Note: You must set day before setting time. 
1\f
E N G L I S H
 C
B
 ACROWN POSITION 
						

							NOTE:Remember to set time for am or pm (sun or
moon).
TO SET DATE:1)   PULL out crown to “B” position.
2)   TURN crown clockwise to correct date.
3)   PUSH in crown to “A” position
TO SET DAY:1)   PULL out crown to “C” position.
2)   Advance time 24 hours to change the day.
3)   PUSH in crown to “A” position
21
E N G L I S H
DAY\bDATE\bAM\bPM\b
SUN\bMOON MODELS
TO SET TIME:1)   PULL out crown to “C” position.
2)   TURN crown clockwise to correct time. Day\fam\fpm\fmoon will also change.
3)   Push in crown to “A” position.
20
E N G L I S H
C 
B 
  
A 
CROWN 
POSITION 
 
DATE 
 DAY 
 
AM/PM 
SUN/MOON 
  
						

							•    The seconds sweep hand shows “seconds
elapsed” for chronograph
TIME, CALENDAR, CHRONOGRAPH This chronograph watch has three functions:TIME
TO SET THE TIME:
1)   PULL out Crown to “C” position
2)   TURN Crown either way to correct time
3)   PUSH in Crown to “A” position
CALENDAR
TO SET THE CALENDAR
1)   PULL out Crown to “B” position
2)   TURN Crown clockwise to correct position
3)   PUSH in Crown to “A” position
23
E N G L I S H
CHRONOGRAPH MODELSReview all chronographs to determine your watch typeTYPE 1
•     Crown position “A”, “B” & “C”
•     Pusher “A” (right) & “B” (left)
•     Hour, minute and small second hands (6 o’clock
eye) show time
•     12 o’clock eye shows “minutes elapsed” for
chronograph
•     9 o’clock eye shows “hours elapsed” for
 chronograph
22
E N G L I S H
 C 
B 
  A PUSHER “A” 
PUSHER “B” 
STOPWATCH 
SECOND HAND   SMALL 
SECOND HAND CROWN POSITION 
PUSHER “C” 
STOPWATCH  HOUR HAND 
STOPWATCH  
1/20 SEC. HAND   
  
						

							NOTE: PRESSING and HOLDING either pusher “A” or
“B” will cause the hands to move continually until the
pusher is released.
STANDARD CHRONOGRAPH 
MEASUREMENT:
1)   PRESS pusher “A” to start timing
2)   PRESS pusher “A” to stop timing
3)   PRESS pusher “B” to reset
25
E N G L I S H
CHRONOGRAPH•     The Chronograph is capable of measuring:
•     Minutes elapsed up to 1 hour (12 o’clock eye)
•     Hour elapsed up to 12 hours (9 o’clock eye)
•     Seconds elapsed up to 1 minute (seconds sweep
hand)
BEFORE USING THE CHRONOGRAPH:Adjust all the chronograph hands to the “0” or 12 hr.
position.
TO ADJUST THE CHRONOGRAPH HANDS:1)   PULL out CROWN to “C” position
2)   PRESS pusher “A” intermittently until the seconds sweep hand resets to “0” or 12hr. position
3)   PRESS pusher “B” intermittently until the hands in the 12 o’clock eye reset to “0” or 12hr position
4)   PUSH in Crown to “A” position 
NOTE: Make sure that the chronograph is stopped
and reset before adjusting.
2\b
E N G L I S H 
						

							SETTING THE DATE1)   PULL the crown out to the 1st position “B”.
2)   Turn the crown counterclockwise to set the date.*If the date is set between the hours of around
9:00 PM and 1:00 AM, the date may not change
on the following day.
3)   After the date has been set, push the crown back to the normal position “A”.
USING THE CHRONOGRAPHThis chronograph is able to measure and display 
time in 1\f1 second up to maximum of 11 hours 
59  minutes 59 seconds. The chronograph second
hand keeps continuously for 11 hours 59 minutes 
59 seconds after starting.
MEASURING TIME WITH THE 
CHRONOGRAPH
1)   The chronograph can be started and stopped
each time pusher “A” is pressed.
2)   Pressing pusher “B” resets the chronograph and the chronograph second hand, chronograph
27
E N G L I S H
CHRONOGRAPH MODELS
TYPE 2
SETTING THE TIME
1)   PULL the crown out to the 2nd position “C”.
2)   Turn the crown to set hour and minute hands.
3)   When the crown is pushed back to the normalposition “A”, small second hand begins to run.
26
E N G L I S H
B  C 
PUSHER “A” 
DATE  CHRONOGRAPH 
SECOND 
CROWN 
POSITION 
PUSHER “B” 
 
SMALL SECOND 
  
 CHRONOGRAPH  HOUR 
 
CHRONOGRAPH
MINUTE
HOUR 
MINUTE HAND 7 
NORMAL POSITION “A” 
						

							*Do not push crown to normal position while the
chronograph second hand returns to zero position.
It stops on the way when crown is returned to 
normal position and its position is recognized as 
zero position.
29
E N G L I S H
minute hand, and chronograph hour hand return
to zero position.
CHRONOGRAPH RESET 
(INCL. AFTER REPLACING BATTERY)
This procedure should be performed when the
chronograph second hand does not return to zero
position after the chronograph has been reset,
including after the battery has been replaced.
1)   Pull the crown out to the 2nd position “C”.
2)   Press pusher “A” to set the chronograph second hand to the zero position. The chronograph hand
can be advanced rapidly by continuously pressing
pusher “A”.
3)   Once the hand returns to zero position, return the crown to the normal position.
2\f
E N G L I S H
TIME MEASUREMENT
RESET STOP 
						

							TIME
TO SET THE TIME:
1.   PULL crown out to “C” position.
2.   TURN crown either way to correct time.
3.   PUSH crown in to “A” position.
TO ADJUST TO A NEW TIME ZONE:1.   PULL crown out to “B” position.
2.   TURN crown either way to move the hour hand inhour increments.
CALENDAR
TO SET THE CALENDAR:
1.   PULL crown out to “B” position.
2.   TURN crown either way to move hour hand. Twocomplete revolutions relative to the 12 o’clock
position will move the date forward or  backward.
This will correct both date and 24hour time.
3.   PUSH crown in to “A” position.
     NOTE:  The date changes automatically every 24
hours.
31
E N G L I S H
TYPE \f
BASIC OPERATIONS
•     6 o’clock eye shows seconds.
•     10 o’clock eye shows “minutes elapsed” for
chronograph.
•     2 o’clock eye shows “1\f20 seconds elapsed” for
chronograph.
•     Chronograph second hand shows “seconds
elapsed” for chronograph.
30
E N G L I S H
 
B 
D  
  A  
   
  
C 
PUSHER “A” 
DATE  CHRONOGRAPH 
1/20 SECOND  CROWN 
POSITION 
PUSHER “B” 
 
SECOND 
  
 CHRONOGRAPH  SECOND 
 
CHRONOGRAPH
MINUTE
HOUR 
 MINUTE 
 
						

							TO ADJUST CHRONOGRAPH HANDS:1.   PULL crown out to “B” position.
2.   PRESS pusher “B” until the hand at the 10 o’clockeye resets to the “30” position.
3.   PULL crown out to “C” position.
4.   PRESS pusher “A” until the chronograph second hand resets to the “0” or “60” or 12hour position.
5.   PRESS pusher “B” until the hand at the 2 o’clock eye resets to the “0”  position.
6.   PUSH in Crown to “A” position.
NOTE:
•     Make sure the chronograph is stopped and reset
before adjusting.
•     PRESSING and HOLDING either pusher “A” or “B”
for 2 seconds will cause the hands to move 
continuously until the pusher is released.
33
E N G L I S H
CHRONOGRAPH
THE CHRONOGRAPH IS CAPABLE OF
MEASURING:
•     1\f20 seconds elapsed up to 1 second (2 o’clock
eye).
•     Seconds elapsed up to 1 minute (chronograph
second hand).
•     Minutes elapsed up to 30 minutes (10 o’clock
eye).
     NOTE:  Chronograph will operate continuously for
4 hours, after which it will automatically stop and
reset.
     NOTE:  The 1\f20th of a second hand does not
move during chronograph function, the 1\f20th
seconds are indicated when chronograph is
stopped and not yet reset.
BEFORE USING THE CHRONOGRAPH, adjust all
the chronograph hands to the “0” or 12hour 
positions.
32
E N G L I S H